CCG2521W Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original burner was eroded on the bottom and flame was coming from undernealth the burner
Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.
Parts Used:
-
Joe from Staten Island, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the shell if the igniter was broken
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.
Parts Used:
-
tao from Frisco, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner would not lite. There was an intermittent spark from that burner.
Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
Parts Used:
-
Dennis from Wheaton, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All the burner caps had badly rusted; tip-off was the smell of gas.
Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.
Parts Used:
-
Kathryn Truax from Key West, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the old had rust out and gas was sipping from the side
I removed the old burner with pliers took off the electrodes. Replace the new burner attach the electrodes placed it back in the burner slot and now it works.
Parts Used:
-
Corliss from Oakland, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
broken insulator for top burner igniter
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.
Parts Used:
-
Paul from Block Island, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
power boost burner went up and all my burners got very rusty on the underneathe side
We were at a loss for a long time without my boost burner and then while checking all the rest of the burners my husband discovered that all of them had a massive amount of rust on the underneathe side of the burners and that worried me. Well as usual my husband took care of my worries when he discovered Parts Select. We both were pleasantly surprised when we found out that you had what we needed. And the installation was less than 5 minutes, WOW, THAT WAS GREAT! Thanx a million!
Parts Used:
-
Michael from Aberdeen, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Parts Used:
-
Arthur from South Burlington, VT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old burner's flame was coming out below the burner.
1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!
Parts Used:
-
Wayne from Midwest City, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Wore out burner and igniter
-
Bruce from Vashon, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replacement of top burner igniter
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3
Parts Used:
-
Godfrey from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner rusted flames coming out the side of the burner
turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right
Parts Used:
-
Lewis from Tomahawk, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
repair range burner
-
ZHENG from PINOLE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Bottm Of Burner Rusted Out
Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.
Parts Used:
-
Paul from Oxford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Parts Used:
-
Bhavni from Richmond, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!