CAQE7001LW0 Frigidaire Dryer - Instructions

When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)

I removed the broken door latch & strike with pliers. Then I pushed the new parts into place

I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

All the symptoms indicated the thermister (located in the exhaust air stream of the dryer) was the problem. Pulled the lower panel off the dryer. Took out the two lower screws holding the door panel on so I could pull the front panel out just enough to get a screwdriver on the screws holding the thermister on. Unhooked the two wires connected to it and hooked them to the new thermister(no need to observe polarity). Put the new thermister in, screwed the door panel back down, put the lower panel on and started drying clothes.

The blower wheel was a bit difficult, but manigable to do yourself.

The repair actually was quite easy but diagnosing the problem was another story. I found out that the dryer would not buzz and vibrate , if I just ran the fluff cycle but no heat. As soon as heat applied, the slight buzzing and slight vibrating would occur after a few minutes. I knew it wasn't the drum bearing, the drum rollers, the rubbing collar on front of drum, idle arm, belt, etc - I had replaced all of them less than a year ago. Anything I found on the internet dealing with the motor was always geared around not running or slow starting or shutting down, loud buzzing, needing a push start to start, etc but that was not the case. So I figured it was the blower housing and ordered that part. However, once I had the machine apart the blower housing seemed to be just fine - nothing obvious, everything tight. The one issue I had was removing the plastic nut with the metal insert on the blower unit that attaches it to the motor shaft which just wouldn't bulge. So I said to myself, the h*ll with it, lets get a new motor, too and remove both parts together which btw, was very easy. So that is exactly what I did. Now with new motor in hand and new blower housing in hand, I easily removed the old motor still attached to the old blower housing together and replaced both which was very easy. Hooked everything back up and no more soft buzzing or slight vibration. Now back to the problem or my guess at this point. I noticed that the rubber mounting bushing in the back of the motor which is used to attached it to the dryer bracket was funking looking - kinda soft and a bit perished. So I am surmising that once heat was introduced, it was enough to soften that bushing enough to cause the slight buzzing and slight vibration but without the heat to soften the bushing a bit, it was quiet and steady. Just a guess but for anyone that has this issue with just heat but no issue with fluff (no heat) check out the condition of that rubber mounting bushing on the rear of the motor. No where on the internet was there any info concerning the symptoms I had and I was flying by the seat of my pants. So am taking the time to get this on record in case someone else has these symptoms and finds it.

1. Loosened the 3 screws inside of the drum
2. Removed the entire back of the dryer (lots of screws)
3. Removed the old vent (there are 2 screws at the bottom that hold it in)
4. Install new vent (put the screws back in)
5. Close up back and proceed to put all of the screws back

Unpluged the dryer, took out the light assembly, unpluged the wires to the unit, replaced the old unit with new unit from Partselect.
Plugged dryer in, problem fixed.
Taa Daa

Thanks, PARTSELECT.

That saved me about $50.00 YAHOO!!

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

spoke with repair person he indicated problem was not door switch but control board, prior to repair person arriving I receive the switch in the mail, I unplugged drier used a small edged screw driver to remove door light switch, removed three wire clips from the old switch, re connected the wires to new switch pushed the new switch into its location, closed the door light went out and the drier started and has ran just fine ever since, saved myself several hundred dollars or a new drier

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

I determined the problem was the fan wheel and housing. I located the part on partsselect.com, Ordered it and installed the afternoon I got it in the mail. Perfect fit.

I have used partsselect before, always had great luck, great prices, always have the exact part.

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

All I did was push the new part into the machine! So easy!