C316W Jenn-Air Cooktop - Instructions

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

First turn the power to the cooktop/fan switch panel off. Next remove the knobs used to adjust the temp of the cooking burners. Next remove the vent grill cover of the cooktop. Remove the two screws on the end of the box which houses the fan switch and burner controls. Slide box back and lift the box up. This exposes the fan swithch and burner control wiring. Remove the two wires connected to the fan switch. Remove the two self-locking washers from the two posts which hold the fan switch in place. A screwdriver works well to pry these off. Slide the fan switch assembly out. Slide the new fan switch in place over the two posts (one on each end) to align the switch. Put the self-locking washers which are packaged with the new fan switch on the posts. These can be difficult and a deep-set socket which is slightly smaller that the washers can be used to push them on. Next put the wires to the fan switch assembly on. At this point I temporarily turned the power on to test the fan switch, being careful not to touch any of the wires. If the fan operates properly, turn the power back off. Then replace the box which holds the fan switch and burner controls. Replace the two screws which hold the box in place. Replace the vent grill cover and the temp control knob tops. Turn on the power.

simply remove and replace th switches using a screw driver an a pair of needle nose pliers

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Replaced the control.

Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.

Parts arrived very quickly & the installation was quick & easy. Will order again.

plugged new one in

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.