C228 Jenn-Air Cooktop - Instructions

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

1. Turned off electrical breaker at electrical service panel.
2. Tested stove top to verify correct breaker was off as well as cook top.
3. Removed front electrical connection panel @ cook top.
4. Disconnected wires to blower fan. (Before disconnection I color coded wires for correct reconnection)
5. Removed the bracket holding the armored cable (protecting motor wires) and removed wires (where connects to electrical connection box).
6. Removed 4 nuts @ blower motor housing and removed blower motor housing and fan.
7. Removed 3 screws that attached the blower fan to the blower motor housing noting or marking the position of the housing to the motor bracket in order to have the same placement position.
8. Pulled the 3 connecting wires from the armored cable protector to separate housing from motor.
9. Removed the fan assembly from the blower motor shaft by using an allen wrench carefully noting the distance from motor face to the fan.
10. Noting/marking the position of the motor mounting bracket connections unscrew the nut and screw that secures the bracket to the motor.
11. Reassemble in reverse order.
Note:
I taped the motor wires tightly together every 3 or so inches to be able to slide through the armored cable.
I also had to rotate the mounting bracket a little to be able to perfectly match the motor housing to the motor bracket.

The new fan motor works great but it's a little bit louder.

Your staff helped me find the updated replacement that worked and when I was having some connection issues helped me get it right!

First I removed the two screws that hold the chrome piece that had the switch in it. I had to disconnect the two lights that light up when the elements go on, had to do that to get to the lock washers that hold the switch in place. Put the new switch in place but couldnt get the new lock washers on the both broke, had to go to the hardware store and get new ones just as little bit bigger, they went on slick. The switch works great again, buy new lock washers before you start

Removed grill cover, two phillip screws on front end of the vent holding the switch assembly in place. Lifted the switch assembly and removed the two wires (plugged into lugs). Then removed the two universal nuts with a 3/8" nutdriver and removed the old switch. Cleaned area and put the new switch in place and replaced the universal nuts, then attached the wires. Replaced the switch assembly and the two holding screws. Then inserted the grill cover and Voila! Finished

Simple replace-new for old

Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY

Went to U-Tube and watched video. New switch has different wire connection pattern from old and requires some scrutiny as to where the connections are on the new sw.

You need a good flashlight!!

Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.

You probably want to look inside as you read this. Most of it is straightforward, except the retaining clips.

First, I turned off the breaker switch. Opening the control housing, I disconnected the two leads and wrote down their orientation (one is silver, the other copper). In my JennAir model, an orange burner light is on either side of the fan switch. The white plastic on the rear is held on by their keyhole shape - just slide them the only way they can. This gives extra working room.

Since the switch plastic was already decayed, I snapped off the whole central square unit leaving the 2 portions held onto the posts by the metal retaining clips. Using a small flathead screwdriver, I pried up the plastic remnants, working around it until the retaining clips came loose/ broke.

The new unit fit perfectly and easily. The new retaining clips needed to be worked down a small circular file to spread the centers out enough for me to work onto the retaining posts. The file was just barely bigger than the existing hole. The clips can be broken if you are too rough or work them too much. After that, I used a pair of snub nosed pliers to push the clips down the posts. They required a considerable amount of force, but they aren't going anywhere anytime soon.

Reconnect the lights, reconnect the 2 leads, and check for any loose wires from other controls and loose parts. Reseat the control housing, turn on the breaker and test.

I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

plugged new one in

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.