C222 Jenn-Air Cooktop - Instructions

Shut off power. Removed cover held in by place by two screws in downdraft area. Removed old switch, removed lens caps from LEDs. Placed switch on posts. Fastened switch to posts using my own nylon lock nuts (not included). Forced leads onto electrical nodes on switch. Put everything back together.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

plugged new one in

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

First I turned off the circuit breaker that powered the cooktop. Then I removed downdraft grate. Took out the two screws that held the control panel. Gently pulled out the control panel and turned it so I could see the bottom of the rocker switch Next I disconnected the two wires from the bottom of the switch. Next I removed the nuts that hold the switch in place. Removed the old switch and installed the new one. Put the nuts back on. Replaced the wires. Slid the panel back in place. Put the two screws back in their holes and tightened them. Easy enough. Part was perfect replacement for the original. Thanks

removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.

Easily removed the old knobs and applied the new ones.

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

replaced old worn silver and white control knobs with new black ones.

Pulled the old one out & inserted the new one. Less than five minutes.

We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

It was very simple. detached front switch panel by removing 4 screws inside top of oven door. Removed knob from old switch and removed nut holding switch to panel. Rotated switch panel to expose guts. replaced wires from old switch to new switch, screwed new switch to panel, replaced old knob. idea came from previous story at this website. Works great.

removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.

removed cover, pulled out old switch, moved each wire from old to new switch, mounted switch, replaced cover.