C221-J Jenn-Air Cooktop - Instructions

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

I removed the old knobs and replaced with the new ones. We also replaced one of the switches which the knobs fit on, because I broke the switch off with a Cast iron skillet.

I lifted off the old knobs, pushed on the new. Easy and the cooktop looks brand new!

our cook top is so old, but no need to replace just yet. so I ordered new knobs to get a new look
thank you!

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

I pulled off the other 3 old knobs. Pushed on the new ones, which pushed on hard, but work. They stick out farther than the originals. They look a little different, but only to me. No one else would notice.
The main part is, it works. A little spenty for my taste, but did not know where else to go and they arrived very quick.

removed all for knobs and replced with new ones

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

1. Turned off electrical breaker at electrical service panel.
2. Tested stove top to verify correct breaker was off as well as cook top.
3. Removed front electrical connection panel @ cook top.
4. Disconnected wires to blower fan. (Before disconnection I color coded wires for correct reconnection)
5. Removed the bracket holding the armored cable (protecting motor wires) and removed wires (where connects to electrical connection box).
6. Removed 4 nuts @ blower motor housing and removed blower motor housing and fan.
7. Removed 3 screws that attached the blower fan to the blower motor housing noting or marking the position of the housing to the motor bracket in order to have the same placement position.
8. Pulled the 3 connecting wires from the armored cable protector to separate housing from motor.
9. Removed the fan assembly from the blower motor shaft by using an allen wrench carefully noting the distance from motor face to the fan.
10. Noting/marking the position of the motor mounting bracket connections unscrew the nut and screw that secures the bracket to the motor.
11. Reassemble in reverse order.
Note:
I taped the motor wires tightly together every 3 or so inches to be able to slide through the armored cable.
I also had to rotate the mounting bracket a little to be able to perfectly match the motor housing to the motor bracket.

The new fan motor works great but it's a little bit louder.

Just slip new knobs on. Simple and works great!!

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!