C221-C Jenn-Air Cooktop - Instructions

I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.

Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.

Oh this was a toughie and I was sweating it out.
With a delicate touch I removed the old knob and pushed on the new knob, 5 seconds

just swapped out the two switches

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires and replaced the connections in sequence. It was easy. BUT, be sure the circuit breaker is disconnected if you want to enjoy the fruits of your labor. I figure I saved about $1100 by not having to buy a new stove top and I now have an almost new one. The cook appreciates it too.

I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!

I turned the breaker OFF and attached the wires to the switch. I then reattached the switch housing to the stove top with the two screws and turned ON the breaker. The fan worked!

First I removed the burner control knobs by pulling them off. Then I removed the screw washers from around the burner control stems. I lifted the chrome plate from around the burner stems. I disconnected the wire plugs from the rocker switch control. I made a note of which one was plugged to what (color coded). I removed holding washers from the two screws on the switch. Then I unscrewed the small screws that hold in the rocker switch and removed the old switch. I screwed in the new switch, put on the new holding washers, plugged the wire plugs back in, replaced the chrome plate and burner stem screw washers. Replaced the burner knobs and the vent fan worked. The hardest thing was getting the holding washers back on as they are too small to go over the screw but open up as they go on. I did not have the right tool for this so used a hammer and a socket with an opening that would fit on the washer so I could bang it down.

We cleaned the rod on the stove and pushed the new knobs into place. This Jenn Air range was made in 1980. Nice to know Jenn Air is still making parts for their ranges. We also ordered new coil elements which fit perfectly size 6 inch and 8 inch.

Just slid off the old burner knobs, and pushed on the new ones. The most difficult part of the whole thing was just being sure that I ordered the correct knobs that used a D fitting. I ordered some a year ago that weren't the correct fitting.

Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.

I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.

Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY

Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.

Hubby & I