C100 Jenn-Air Cooktop - Instructions

First I turned off the circuit breaker that powered the cooktop. Then I removed downdraft grate. Took out the two screws that held the control panel. Gently pulled out the control panel and turned it so I could see the bottom of the rocker switch Next I disconnected the two wires from the bottom of the switch. Next I removed the nuts that hold the switch in place. Removed the old switch and installed the new one. Put the nuts back on. Replaced the wires. Slid the panel back in place. Put the two screws back in their holes and tightened them. Easy enough. Part was perfect replacement for the original. Thanks

took old knobs off replaced in 3 minutes

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!

removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.

Ordered new cartridges

Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Shut off power. Removed cover held in by place by two screws in downdraft area. Removed old switch, removed lens caps from LEDs. Placed switch on posts. Fastened switch to posts using my own nylon lock nuts (not included). Forced leads onto electrical nodes on switch. Put everything back together.

Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation

Removed old knobs and installed new. No tools were required.

Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.

Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.

removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.

Remove and replace grease filter.