BEV7110 Hardwick Wall Oven - Instructions

Unscrewed and pulled the door off and then took the three layers of the door apart in order to clean off the burned-on goop and remove the old and insert the new seal. The last screw was rusted in and the drill stripped it so that it was impossible to remove. I levered the remaining two layers apart, holding them open with screw drivers, and inserted the new seal. Had to be careful with the shaping of the metal core of the seal and the distribution of the sealing fabric. Phew! I saved the screws from each layer separately by taping them to the counter in the order of removal. This made reassembly easier. Getting the door back on was a bit difficult and I needed another pair of hands to help me.

1.remove the trim around the door (8 screws)
2.remove over glass panel (part with the handle)
Caution; the springs on the door are exactly set for the weight of the door. When we removed the outer glass panel, I almost killed my wife when the door slammed shut.
3.Remove inner metal cover (6-8 screws).some of these screws were baked pretty tight so I used vise grips on their little heads to convince them to get turning.
4. To get the door window out you must also remove the inner enamel baked cover, held on by 5-6 screws from the back. This is also the pieces which holds the door seal in place, so it is a good time to change that as well.
5. After cleaning up all the broken glass from the old window, the new window slides right in - perfect fit!
Reverse the steps to put it all back together.

From the time the glass broke until it was completely repaired took only six days! Pretty amazing for a twenty year old oven.

Older model oven with model number worn off. Photo with the 1" grid made it possible for me to find the right size part.

You only need a phillips head screwdriver to install this seal, but it is a bit tricky to line up the new seal and the fiberglass insulation inside the door, so take your time and make sure everything lines up and is tucked in before tightening the screws. Probably easier to do with 2 people (especially getting the door back on the spring loaded hinges) but I was able to do it solo without too much difficulty.

I dissasembled the entire door..lots of screws and watch you dont drop the glass pieces...also keep them in order so you dont get confused on what goes where. I cleaned everything nicely and installed the new seal and everything went together perfectly and looks and works like new. I recieved my part by mail very quickly and the price was MUCH better than my local repair shop.

Purchased 2 piece broiler pan from this site

Serviceman took out broken glass by removing door and separating front of door from back of door. He carefully removed all broken glass Then replaced with new glass and fastened door together . He did repair in 20 minutes. Oven is like new. Thank you very much for still stocking this part that allows me to keep my oven repaired.

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I pulled off the facia from the microwave/oven. Unscrewed the plate holding the microwave and slid out the microwave. The microwave and oven are a unit. I unscrewed the oven from the hole it sits in and slid out the oven and set it on a sturdy chair. Then I unscrewed (6 screws) the bracket that holds the microwave to the oven. After that I unscrewed (14 screws) the top sheetmetal plate on the oven and slid that around behind the oven. Then I unscrewed the grounding strap inside. Did the 2 screws on each side of the oven holding the fan unit and slid that out. Undid the 2 wires plugged into the motor and the 2 screws holding the fan motor. Then I slid off the fan from the old motor and slid it onto the new motor and reversed the whole process.

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads

Removed door (that was the most difficult part)
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!

I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.