AT21M9A (DD65A) Admiral Refrigerator - Instructions

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

very easy

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Screwed in light bulb and glass protector

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Ordered the entire seal kit for repair and seal of the basket and hub. One of the challenging tasks was to pull the drive bell off. If you crack or break it, no big deal, you won't reuse it but to make it simpler, use whats called a wonder bar or flat bar and use the hex head bolts in the base of the basket for leverage and work on opposing sides of the bell and it will slowly come up off the shaft instead of using a drive bell tool you'll only use once.
Once you pop that off, take the front panel off and lift back the top to expose the entire interior and exterior basket. remove the bolts in the interior basket and pull out to expose the exterior basket. Now, you need to get that honkin hex nut off the transmission output shaft which was probably the hardest part of the job. Here's the trick to get that off. Grab an 8 inch pipe wrench, reinstall the two hex bolts back into the hub assembly you just pulled out to remove the interior basket but leave them high enough to get the flat bar between them to stabilize the hub and use the pipe wrench to remove the giant hex nut. Once this is done, its all down hill.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Took out socket, replaced new bulb in new socket and plugged in. Easy!

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch