Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ASD2514ARA > Instructions

ASD2514ARA Admiral Refrigerator - Instructions

All installation instructions for ASD2514ARA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ASD2514ARA
526-540 of 822
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Both sides stopped getting cold

  • Customer: Lynda from Gary, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

Ice Maker quit making ice

  • Customer: John from Columbia, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.

Ice maker did not work

  • Customer: William from Carmel, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I put in a new ice maker because it was not in very good condition. The water valve had a very slow leak which allowed water to freeze on the way to the ice maker and plugged the line. This problem was in one of your repair articles all of which were very welcome

the 2 yr old icemaker tray had deterioted and the ice stuck

  • Customer: Richard from Mt Airy, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.

the water line broke and the new water line was leaking due to bad connector

  • Customer: Vincent from Brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
repair was just like in the video. no surprises

No ice. Web site explained what to check for ..

  • Customer: Stewart from Ventura, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just followed directions.Which were clear as could be. I think it took longer to clear the freezer, than to replace the ice maker. Thanks so much.

Replaced ice maker

  • Customer: Christopher from Cave Creek, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator and truned off water supply. I then removed old ice maker by first removing screw holding mounting bracket with 1/4 inch nut driver. Then I carefully pulled up and out on the ice maker to remove it from mounting brackets on the side of unit. Once free, I was able to access the wiring harness in the back and remove it from the unit by compressing the clips and gently pulling with an even pressure. Now that the old ice maker was detached I took it to my counter and removed the on/off switch rocker bar and wiring harness. I attached these two pieces to the new ice maker. I then plugged the wiring harness back into unit and lined up the mounting brackets on the side wall and did a reverse tilt to downward pressure onto brackets until they clicked in securely. The last step was to screw in the mounting bracket with nut driver. Turned on water line and plugged machine back in. It took about an hour and a half before it produced its first harvest of ice, but has been working like a charm since.

Ice leaking water.

  • Customer: Paul from Madison, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video on the sight and that was almost all I really needed. The only thing I would add is that it took me some time to get the drawer freezer door off. Lift the front straight up. Don't pull the door slides out.

No water for the ice maker

  • Customer: William from Carmel, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The only part I needed was the Valve assembly. I checked for frost and found none. I took out the Ice Maker and found it was in poor condition but working. I did put in a new one but with the same problem. I finally read the comments from your costumers and found one place that told about a leaky water valve that was letting water drip into the ice maker so slowly it froze and blocked the valve. So I put in a new valve and thawed the pipe and allis well. What made this job so easy was the costumers comments and the best was the one day delivery of the parts. Thank you for all your help.

Ice Maker worked sporadically and then started dropping water into bin, make a large chunk.

  • Customer: Harold from Spring Branch, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Was very happy with the experience of using your company. The man on the phone was helpful. The icemaker shipping was only about $7 and got here in a couple of days. I liked the video, and then including a link to the video with the on-line confirmation. Was not quite sure it was the icemaker or the metering valve on the back, as the latter would make a little grinding noise, but the symptoms matched the dumping of water into the bin. After replacing, everything is working well. The only difficulty was the wire harness plugs into the other side of the back of the box than in the video and I found it a little difficult to route the wires correctly as they seemed too short. But a little trial and error solved that. My model is freezer on the bottom and I didn't notice that the little detachable funnel wasn't quite seated and it was necessary to reinstall, making sure the funnel stayed in place correctly. That was my own error. My overall experience was excellent and I would not hesitate to recommend PartSelect to anyone with an icemaker problem. I'm only sorry I lived with a recalcitrant ice maker for a couple of years before finally acting on it. I am glad I found your website! Lee in Texas

Not making ice, leaking water.

  • Customer: Robert from Youngstown, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaking mechanism replaced with new. Works better than ever

ice bin drive ring was cracked

  • Customer: Jesus from Santa Maria, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed torx screws and replaced ice bin drive ring.

Condensor Fan going bad

  • Customer: George from Hickory, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!

Ice Maker would not make ice

  • Customer: Philip from Hoschton, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Quick repair especially with YouTube video; took less that 15 mins including moving ribbon cable & fill wire. Saved at least $200.

Ice cresents froze together in one big lump

  • Customer: Lloyd from Stilwell, KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Simple replacement of the icemaker solved the problem. I suspect the icemaker was overfilling resulting in water flowing into the ice reservoir.
All Instructions for the ASD2514ARA
526-540 of 822