Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ARG7300W (P1141296N W) > Instructions

ARG7300W (P1141296N W) Amana Range - Instructions

All installation instructions for ARG7300W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARG7300W
166-180 of 220
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven would not heat up. inoperative

  • Customer: frank from racine, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
looked on line for ideas. guessed and gave a try. used parts select in past.great service and price. removed back panel on stove, removed lower panel to access ignitor. removed 3 screws and connector. re install new ignitor and reverse order.

Oven would get warm but not reach baking temperature

  • Customer: DAVID from ROCHESTER, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched video on YouTube of a guy fixing the igniter problem. Sounded like the same problem I had and the repair looked relatively easy for me (who has never repaired an oven in any way before).

The right front burner quit lighting, the igniter was weak.

  • Customer: Bobby from Boulder, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the burner by unscrewing the two screws and lifting out the burner/igniter together being careful to not let the electrical connection come apart. If it does then you have to take all 4 burners off so you can lift the whole oven/burner top. Disconnect the old igniter by (more than likely) drilling out the old screw, if you are lucky maybe the old screw holding the igiter will actually unscrew. If not, you can put a new screw in to hold the new igniter, put it all back together and youre done.

Igniter glowed but didn't ignite the gas

  • Customer: Elmer from Ninilchik, AK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I first unplugged our 12 year old stove, turned gas off, removed broiler pan, removed shield under broiler pan, and removed one nut holding V-shaped flame diffuser in place. This exposed the igniter at the rear of the oven. There are three screws securing the igniter shield, remove them. Next I removed the storage drawer to gain access to another shield in the back corner of the oven protecting the plugin for the igniter. There are two screws holding this shield in place, remove them. This exposes the igniter plugin. Carefully unplug the igniter. Remove the old igniter from the igniter shield assembly. Insert the new igniter and screw the igniter assembly back into place with the three screws. Go under the stove and plug in the new igniter. The hardest part for me was putting the shield under the stove back with the two screws. Put the storage drawer back. Reinstall the flame diffuser. Place the shield over it and the broiler pan. Plug the stove in and turn on the gas. This solved the problem. Thanks PartSelect.com.

Oven no longer came on

  • Customer: jeffry from Sussex, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm

Ignitor would not ignite the oven

  • Customer: Fletcher from Greenville, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher

My oven would not ingnite when turned on. I could see the igniter glowing, but it wouldn't get hot enough to open the gas valve.

  • Customer: Steve from St.Amant, LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
It was a little difficult, but all in all not to bad. Getting the drip pan out was simple. Just take out all the screws. Oh yea, you will have to take off the bolt in the middle of the deflector. The igniter wire was a little to short, so I had to use needle nose pliers to hold the wire while unplugging and plugging the new igniter. Be careful not to break the delicate igniter. Screwed it all back together and it works just like new.

oven light replacement

  • Customer: martin from portland, OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

oven wouoldn't light or was very slow to heat up

  • Customer: George from Laramie, WY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed and replaced flat igniter

Oven rack with melted plastic

  • Customer: Anthony from New Braunfels, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered new oven rack, they don't fit, can I return them??

ignitor would glow but oven. would not turn on

  • Customer: Manuel from Del Norte, CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
unplug oven . removed v-shaped plate on bottom of oven .after i removed racks. 15 min.not including getting tools and after research on Partsselect videos. removed mounting clip/gaurd holding igniter in bottom back side of cavity,held by small screw. removed bottom storage drawer on bottom of oven door.once removed had access to protective shield held on by two sctews. Almost all the way to the bottom back of range . unclipped wires coming fr. igniter .pulled out igniter fr. oven and removed mounting/protective casing. Installation should be in reverse order ,but in the attempt to install mounting clip back on igniter ,the element broke. so it's very fragile. being on a budget or no budget at all i''ll have to wait for a few more months again to be able to get a new one..REMEMBER-- very fragile and no warning labels........hope it saves you time and $$$

Oven igniter would glow, but not light oven

  • Customer: Stephen from Anaheim, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the door, bottom cover (inside oven) and flame spreader. I had to remove the screws around the pan in order to remove it as well, and the burner (pipe?) The replacement part is amazingly fragile, and a touch on the tile caused it to break, necessitating a trip to an older appliance store for another igniter. This replacement came with a female plug in the connector, which wouldn't work with the one in the oven, but fortunately I was able to use the wire from the original and the ceramic wire nuts that came with the replacement. The part from PartSelect would have been an exact replacement. Make sure that the burner pipe fits over the nozzle on the bottom or the fire will start in the back of the oven instead of inside.

Oven did not heat

  • Customer: Maria from Lorain, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed metal housing under drawer plugged in new igniter and replaced 3 screws...easy! and im a female!!

Door wouldnt shut evenly.

  • Customer: David from Westlake, OH
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

Burners would not light everytime they were used.

  • Customer: Blaise from Deer Park, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.
All Instructions for the ARG7300W
166-180 of 220