ARB9059CS (PARB9059CS0) Amana Refrigerator - Instructions

Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

Took out 2nd new filter $43.00 each that clogged in less than 2 weeks each and installed in 2 mins. this bypass and ice and waterr work perfect.Thank you, thank you for your exceptional service ordered part and it came next day without extra charge,great service.

Installed new parts and it run like new

Opened up the compartment where the old filter was located, twisted it to take it out (be careful not to spill water in the filter!), and installed the new one. Even a 64 year old woman had no trouble!

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Removed the left hing side and replaced it

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I first repalced the ice maker (Parts Select) and the unit still did not produce ice. Then following a U-tube video I tested the resistance on the water valve with a multimeter. It failed. Ordered a replacement water valve from Parts Select. Received part 2 days later. It took 15 minutes to remove and replace failed valve. Ice maker operates perfectly after repair.

I unplugged the refrigerator. Then removed the ice tray. Then removed the screw holding the ice maker secure. I had a little difficulty lifting the ice maker off the clips on the side of the refrigerator but was successful. Then unplugged the wire harness from the back of the refrigerator an lifted the unit out. Removed the wiring harness from the old unit and installed it on the new one. Then positioned the new unit so I could plug the harness in the refrigerator and lined up the clips to attach it on the side of the refrigerator, being careful to line up the water distribution tube. Replaced the screw to secure the ice maker and plugged the refrigerator back in and it is working very well. I am very hsappy with the repair

I attempted to do the repair as cheap as possible and did not think the problem through completely before ordering the water source value kit.since it was the cheaper of the two parts that could be causing the problem. What I missed was the fact that when the bail is raised to turn the ice maker it also turn the water off and it was not leaking so I should have recognized that the value was probably not the problem. So I ordered the ice maker and it arrived in one day as did the value and I was back in business of making ice chunks and not ice blocks! :) PartSelect has a wonderful turn around on shipping parts and great customer service folks to converse with!

After receiving the new ice maker assembly I placed the new part next to the old one to see what I needed to transfer from the old to the new. After removing the wiring harness and a few small parts, I placed them on the new assembly. After that it was a snap which timewise took about 15 minutes. I am pleased to say the ice hopper is full and being replenished very efficiently.