ALW895SAW (PALW895SAW1) Amana Washer - Instructions

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

Followed video on PartsSelect website, they made it real easy.

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

I removed the front lower panel. I disconnected the springs holding the motor to the chassis. I removed the belt off the pump pulley. Pay attention to the way the belt runs from the pulley and through the pump. This will aid in placing the pump back on so the belt runs correctly. Disconnected the wires, removed the capacitor bracket so I could take the motor/pump unit out after I removed the 4 bolts holding the motor/pump unit. Removed the 3 torx screws holding the pump to the motor. Matched the new pump to the old to make sure the new one was correct.

Installed in reverse order.

I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.

removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse

I seemed to have a more difficult time changing the pump out than others who had left their instructions on line prior to me.
What I has to do is remove the 4 bolts that secured the motor & mount to the frame. I then unplugged the wire harness from the motor leads.
I removed the belt tensioning spring & removed the belt.
I then removed the motor, motor mount and pump assembly. Turned it upside down & removed the pump. When installing the new pump you will need to remember how the belt was routed. A local parts house actually gave me a xeroxed schematic that showed me how to route it. A real life saver.
After that I turned the assembly right side up, bolted the mount into place, installed the new belt onto the large flywheel, attached the belt tension spring, plugged in the wiring harness and ran a rinse cycle. No leaks. Good as new.
Yes. It took a little longer than expected. But it was alot cheaper than having a service man do it.

I was able to remove the belt because it was worn through. However, I was unable to remove the pump as described in the instructions because I was unable to get my torq wrench to the bolts. I ended up having a repairman come in.

replaced belt that was wore out. decided to replace pump while I had washer apart.

Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.