ALW221RJW Amana Washer - Instructions

unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.

I think normally the problem is caused by the Brake Rotor Lining Assy (item #50 on the diagram). It has a brake lining facing down that makes contact with item # 51. It turned out that I had grease & grime on these parts, thus the brake is not taking grip & causing squeaky noise. All I had to do was to clean the parts & put them back. I bought the part (#50) - P/N 2347192, but it was a whirlpool part that didn't fit my Magic Chef. Some parts fit both brands, but this 1 didn't. Here is the procedure:

1. Unplug washer.
2. Move unit away from wall.
3. Tilt it back far enough to work underneath. Support the front with lumber.
4. Pull out cap (#58)
5. Remove ring clip (#57)
6. slide out everything from #53 down. Keep them in same order for re-installation.
7. There are 6 ea screws (#53) that hold item #52 to item #45. It is spring loaded by item #47. Item #53 has a 5/16" hex head. Use 3 ea. #10-24 hex head screw, at least 1.25" long to assist in compress/decompress the spring tension. You can buy them from a hardware store.
8. Take out every other screw (#53) & replace them with these 3 longer screws for remove/re-installation of item #52.
9. Take out the remaining 3 ea #52 screws.
10. Go around & back off each of the 3 longer screws to decompress the spring.
11. Remove item #52, & everything from #48 down will come out.
12. Clean or replace what you need.
13. Do the reverse to put everything back.
14. There is an item within #59 that looks like a miniature bearing. I would put some grease on that & on item #55.

The Repair went well . I had the hose on in about 30 seconds . The best part about this ordeal was the ease of finding the part on your website , and the speed of the delivery . I had my part in about 2 days , put it on and back to the fun part of clothes washing . I would recomend this company to everyone. Thanks, Rick K.

Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.

first I thought there is a problem with with hoses.problems like filter or hoses blocked.after I opened the hoses they were fine .Water was going out with power .Then I opened the valve connected to the hoses . I checked these hoses withe help of a 12 volt battery . the valve was not opening so I came to the conclusion that this part is broke.is not easy to change this part.Small place and hard to unlock the hose inside .They could design this much easier with just using longer hose.But I think then nobody will call service dept.

Unplug from power Source,turn off water supply,Remove 3 screws that hold the Control Panel in Place.Remove knob, lower assembly, unplug wire Connector,using pliers , compress vacuum hose clamp,remove vacuum hose,remove screw holding switch in place,depress plastic tab that prevents movement,twist switch assembly to remove.Reverse procedure to install new switch.

Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

1. Pulled top off (liquid softener dispenser section)
2. Put 2 socket extension and a 13 mm socket together with socket wrench (tool).
3. Insert tool with 13mm socket end into old agitator and unscrew bolt.
4. Remove tool and then remove old agitator.
5. Turn old agitator upside down to remove bolt.
6. Insert new agitator where old agitator was in washer.
7. Insert bolt.
8. Insert tool with 13mm socket end into old agitator and screw in bolt.
9. Pop top back on.

Hardest part was finding extensions because one wouldn't reach.

Popped off bleach cap on top then got socket and long extension removed bolt, cleaned a little then replaced new agitater top.Replaced bleach cap and i was done.

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

Leaned washer forward, removed clamp and old hose, replaced with new hose, reinstalling clamp.

Researched "trouble shooting guide" Parts Select Website--

2 possible part failures - (1)--water fill valve inop-per Parts Select Web - 74 percent change of this unit failing.
(2)--pressure line fractured - 24 percent chance of this unit failing......

Ordered both parts from Parts Select -

Replaced water fill valve (possible solenoid failure--(although a little difficult to get at valve replacemnt was easy - total porcess took a little less than an hour).

Needless to say - problem solved with valve replacement, this machine should be "good" for at least another 5 years.

Thanks for your kind help and most important - the easy to use data...........

Spence Merrell
Dayton, Nevada

I used a screwdriver to release the front side of the waaher top from the clips and tilted the washer top back. I then released the hose from the water valve and took out the mounting screws at the back. Replaced the valve and hooked everything back up.

I'm not a washing machine technician but I did nurse a new Kenmore machine for 23 years and was ready for a replacement. Craigslist advertised a Maytag I was interested in and I bought it with the seller's assurance that it worked perfectly. It didn't and I went online to try and figure out what might be wrong. Clearly, the tub was traveling beyond it's design limit and I suspected a spring or two might be involved. Somewhere online, I found the illustrated parts diagram and then went looking for additional information. To my extreem delight, I came across a do it yourself repair video that demonstrated the procedure well enough that I was completely confident I could make the repair with little effort. That video was one of several service related appliance videos offered for free throughhttp://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/index.html/ The final consideration was whether I could buy the replacement suspension springs and snubber ring for less than I paid for the washer. I found PartSelect and within minutes, I had the parts ordered. The parts arrived within 4 or 5 days, as promised, well packaged and in perfect shape. This morning, using the video as a final reference and the new parts, I completed the repair with only a minor hitch. Without the special spring tool used in the video, I struggled a bit with getting the new springs attached. That's where my wife came in handy (after all, she was movitated). Having her tilt the drum toward the spring landing made it much easier for me to stretch it into place using an adjustable locking plier. I actually enjoyed the whole procedure.

Removed the old hoses and screwed on the new hoses.