AFI2538AES Amana Refrigerator - Instructions

Replaced ice bin complete with wheel. Easy fix and resonable.

It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.

I almost ordered the Door Led Board but read where somone else had the same problem and ordered the HV control board. Pulled the refrigerator out to gain access to the back of it. Safety tip make sure you unplug it. Located the HV Control board, release the wire connectors from it, and simply replace the board. Plug it in and follow the directions which come with the new HV board on programing it. Entering the Code off the units Data plate.

I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part select. I will order parts from them again.

Thanks for helping me fix my fridge.

Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.

Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble the refrigerator, it was fully operational. Very easy to do and only required a few tools.

This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

After removing the shelves and drawers to gain access to the End Cap unit. I removed the screws and detached the unit which was a little tricky without any actual drawing details. After removing the unit I had to undo the plastic temperature control arm without breaking same. I then transferred the shelve draw slide and reconnected the control arm assembly to the new End Cap unit . At that point it was a simple installation, the drawer works better then new. Note: I did find some loose packing material behind the End Cap assembly unit that might have caused the failure of the drawer and door mechanism during its original factory fabrication. Other than that the project was a complete success. Dick S.

Took off old cover 3 screws...removed metal track and 2 other plastic sliding bars for air flow..put on new cover and carefully put back deli cover on plastic pins..easy fix...lousy design by maytag again! Thanks to PartSelect easy and prompt service and delivery!

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

Unplug Refrigerator access panel in the rear unscrews- disconnect the wire harness from circuit board- remove board (snaps out). Insert new board ,attach wires close access panel. Plug refrigerator in. reprogram fridge code with ice maker controls code is on label with model number and s/n number.

It was a very simple operation to replace the parts and required essentially no tools, just a small screwdriver to pry up a tab for removal of the chanel on the front edge of the frame. This chanel had to be removed from the old crisper frame and installed in the new one. In addition the crisper control" had to be popped out of the old frame and into the new frame. Most of my time was spent cleaning.

Removed the back cover for the HV Board. Unplugged the cables from the old board, put the new board in the same exact way, connected the cables. Put the back cover back on. The hardest part was the programming. You may need to read it again in order to figure it out, but not too difficult. Face it there are only so many buttons, eventually you will go "AH-HA" ! I saved myself around $250! I will most definately use this site if I have other appliances that do not work! You guys rock!

~Lisa~