ADE20L4W Admiral Dryer - Instructions

Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

It took me a bit to figure out how to get the outer case to come apart (there are two spring-loaded latches under the front edge of the lid, had to insert a putty knife at just the right spot then lift up the lid). Once it was taken apart, I manually spun the drum to see where the noise was coming from and it was obviously coming from one of the two wheels that support the rear of the drum. Took out the drum after sliding the belt off and replacing the wheels was a piece of cake. They are held on by E-clip style retaining rings, which I destroyed when removing them with a pair of pliers. Luckily the new set comes with new retaining rings, along with the required washers and spacers. I also replaced the metal pins that the wheels spin on, since mine were showing wear and I wanted to make sure it wasn't going to keep squealing after I was done! All in all it was pretty easy! Before you take the belt off, make sure you take note of how the belt winds around the tension wheel so that you put it back on correctly! My girlfriend was VERY impressed that I was able to fix her dryer for about 1/10 of what it would have cost to get a new one!

Real easy I have resurrected my dryer may times so this was easy to replace the belt and idler pulley

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

Hinged open the top of the dryer. While dryer was running I tapped on the thermostat. The heater came back on. This verified the problem. Unplugged the thermostat, unscrewed it and replaced it.

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Unplug dryer

Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.

After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.

The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.

The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.

From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Watch the video. Very, very easy

my ex husband took the top and front of dryer off and removed the drum and belt. he pulled off the worn roller and replaced it with the new one. we put the drum in backwards and had to turn it around but all went well and the dryer is quiet again!!!

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

I opened the top then i did change the heater element kit only one screw out and finaly replace the temperature switch, again one screw out was realy ease was my first time,the professional online help my, every one can do it thanks i appreciate your help.H.E.K.P/N AH2162280 - temp/switch p/n 31001449.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis