ADB3500AWW Amana Dishwasher - Instructions

Tghe old one snaps off and the new one snaps right in .

This was very easy to fix, just pop out the old one and install the new one. I saved $60-$75 on a repairman coming out to fix the thing in 5 minutes. Truly, I received the part from PartSelect in two days after placing the on-line order. We were up and running in between loads.

unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....

Take out the old parts and clean all the ones to be reused by power washing with garden hose and/or compressor blasting. Put it all back together. BE VERY CAREFUL NOT TO PUNCTURE THE ACCUMULATOR FILTER! THE TORX SCREWS ARE RIGHT NEXT TO THE FILTER SO IF YOU SLIP AND DROP THE TOOL, THE FILTER WILL BE TOAST!

THE DISHWASHER WORKS PERFECT NOW!

I had to force the door open, due to a broken handle/latch.
Ordered assembly with help of order desk to assure correct part number. Arrived within 3 to 4 days. Not sure but very fast. Only had to wash dishes by hand once.
Turned off power to dishwasher, my electrical panel is clearly marked with switch for dishwasher. No guess work there.
3 min. to remove old assy. 3 min. to replace with new part.
I might add that I am a 67yr. old female. So if I can handle this repair, anyone can.
Saved repairman service call, or purchasing a new dishwasher.

Removed the old broken wheel and popped in the new one. The best part of the entire problem was searching this website and finding the part quickly. Granted the shipping was almost double the price of the part, but still under $15. Searching and delivery of the part was fantastic.

The repair was simple. I did a Google search for the part online. PartSelect.com was the 1st site to appear. The link brought me right to the part I was looking for. I order the part (2 just so I would have one down the road in case this happens again) and the next day it was on its way. I simple popped of the old part and installed the new part... works like it is supposed to now. Thanks for the help PartSelect!

Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.

Great pictures of components on this website confirmed what part to order.

Shut off water feed to DW and disconnect power to DW.

Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.

Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.

Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.

Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.

Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.

Removed the screws on the door of the dishwasher, lifted up inside of door to get to the latch assembly, unplugged the 2 sets of wires, removed the old broken latch. To install new latch did all of the above in opposite order.
Very simple, quick easy fix. The only thing that might be an issue for some people is that you need a set or torx head screw drivers. (nice little set at Home Depot for less than $10. I'd say.)

Ordered the part easily using model number and schematic on web site. Part came in two days. Unfortunately, they had the right part number but the wrong part was pulled and sent to me. I called and they resolved the issue over the phone and sent me the right part in two days. Part snapped right on in 5 seconds and I was back washing my dishes that evening.

Remove the racks top and bottom. The Station D seals are at the far back on the tube that supplies water to the top and middle spray heads. Unsnap the old one and snap in the new - it only goes one way! This will repair the seal aroound the tube that supplies the middle sprayer and restore pressure to all 3 heads. Repalcing the screen accumulator is harder. you need a torx driver. remove the little thumb nut on the bottom sprayer and remove the sprayer. Then remove the tube where you just replaced the D station. (You of course could have done this earlier if you were doing both repairs) then 6 screws on the impeller housing. Now remove the 1 torx screw on the impeller and pull the impeller up and off. Remove the 3 screws on the cover and 2 screws on the accumulator. Clean all the old food scraps that are clogging up the works and reassemble in reverse order. Washer is working again!!

Snapped on new wheels

I separated the door from the interior door liner by unscrewing the "torx" screws along the edge of the door interior (about 12 screws). I unscrewed the circuit board cover and removed the old circuit board and disconnected the wiring harnesses that attached to the circuit board. I reconnected the wiring harnesses to the new circuit board, put the circuit board back into its holder and cover and reattached the door liner to the door. I flipped the house circuit breaker for the dishwasher power on and turned the dishwasher on. It works like a charm!

Easy to do. Order the handle (with latch assembly) rather than the latch assembly. It's cheaper and it contains both parts (handle and latch). Turn off the power. Use a T20 star tool to remove the screws inside the door. The latch assembly will fall right out as it uses the screws holding on the door. The hardest part is getting enough nerve to pull the two electrical plugs out. They are really tight and need some pulling with pliers. You might want to put a dot on the wire connector with a sharpie so you can put it back in the right side up. Connect the wires to the new assembly, place in door, put screws back in. Turn on the power. Done. I called a repair place and asked for a estimate for this job: $150-200 with parts. I did it in 10 minutes for $30 worth of parts.

Stuck new wheel on, time to find and order part on partselect 2 min, time to open package and install part 1 min.

Total job 3min.