ADB2200AWS Amana Dishwasher - Instructions

Simply popped the new cover in. My part by the way was really easy to identify on the website, easy to order and arrived in a very timley fashion!

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

I removed the lower wash arm held by a single center plastic coated nut with pliers.

I then removed the six pump housing screws and the three filter cover screws.

This allows access to the pump impeller which is held by one screw. Once it is removed the filter plate, chopper and motor seal can be removed.

I actually had done this before to find a noise. At the time I noticed the impeller had become shorter due to plastic breaking off the impeller. It still fit the motor shaft so I just cleaned out the plastic and screwed it back on. I did not check for water leakage until I noticed loose flooring material a couple weeks later.

This is the mistake I made. The impeller is made so it presses down upon the motor shaft seal expanding it to seal out water. Because the impeller was missing the lower skirt it was too short to but enough pressure upon the seal to stop leakage.
Never use a impeller which is damaged in any way.

Due to this error I have had to buy a motor assy also. It was destroyed by the water.

Removed all the screws on the inside door panel,then I removed the old latch assembly and two electrical plugs. Next I installed the new latch and connected the two electrical plugs. I then replaced the inside door panel and the screws.The dishwasher now works like new after this simple repair. BE SURE TO DISCONNECT THE ELECTRICAL POWER BEFORE MAKING ANY REPAIRS!!!!

First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

The first thing I did was read the all of repair stories that others had submitted. Then I set the timer and chucked up the Torx bit in my electric drill/screwdriver. There are 10 Torx screws on the inside of the dishwasher door and they came out very quickly. The top two screws hold the latch in place. I lifted the inside stainless steel cover to get acces to the latch. There was enough slack in the wire that I was able to remove the latch from where it was and extend it above the door. This let me lay the stainless steel liner back onto the inside of the door without removing or disconnecting the soap dispenser. Thus exposed, disconnecting the connectors from the old latch and reconnecting them to the microswitches on the new latch was a breeze. Once connected, I reinstalled the latch assembly, repositioned the liner correctly and replaced the ten screws. The entire job, including putting my tools away and cleaning up took eight minutes. I did it on my lunch break. The eight minutes included pulling the circuit breaker and reconnecting it (very important, that step). The new latch/handle assembly completely fixed the problem.

After looking the situation over, I decided to remove the entire lower rack and place it on the counter where I could see better. I specified I needed the front tine (part # 24), but received both front and back tines). I used the screwdriver to help slip the old piece out of the plastic clamp end. I broke the end of the first clamp, but fortunately, replacement clamps were also included in the kit. I decided it would be easier to assemble the tines and the clamps first, and then install that into the rack, so I had to remove the other plastic clamp and did so successfully. Then holding the assemblage in place to see just where to snap it into place, I proceeded one clamp at a time and installed it. I kept the new back tine guide just in case someday that one wears out too.

Removed screws around perimeter of interior door panel. Latch was loose at this point so all I had to do is disconnect 2 wires and reattach those 2 wires to new part, position new latch in the proper place and fasten interior panel into origianl position. That was it!!!!

Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

I was able to remove the old handle and place it on the new basket - using only a screw driver.

First I had to go out and buy a Torx driver set, then I removed all of the Torx screws around the inside of the door panel. After that the door latch was free and I saw my problem, a broken retainer on the door latch assembly. I ordered a new door latch assembly and when it came in I removed the two electrical leads, set the new door latch assembly in place, attached the two electrical leads and reassembled the door panel with Torx screws all around. The new latch worked just like it was supposed to.

It was my first time repairing a dishwasher. I was a little worried. I also wasn't sure about how to remove the drain pump. Well, the hardest part was just getting the dishwasher out from under the counter. I did find a crimp in the drain line that probably contributed to the original pump going out. I fixed that, removed the old pump by removing one screw holding a stablizer bracket and twisting the pump connection. The original bracket is needed, so I removed it from the old pump, attached it to the new pump and reversed the removal process and secured the pump by reattaching the stabilizer bar with the single screw. I then slide the dishwasher back under the counter. Runs great. Easy repair. The part was shipped and delivered on time. Very impressed with the process and will order my appliance parts from you in the future.

Had to insert putty knife in the top of latch opening and press up to release the latch so the door would open.

Turn off electric to unit.
Removed the 12 star screws on the panel inside of door.
Pulled out the two wire plugs from the door latch unit, had to use a screwdriver to help push out the metal pronges.
Insert the plugs in the new unit and align the latch pivot point on the door and the two holes with the holes for the inside panel.
Replace the screws.
When the door is closed the latch will be pushed into place and the door is held closed.

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.