ADB1600AWW4 Amana Dishwasher - Instructions

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.

I am NOT an appliance technician. I am simply a somewhat handy homeowner. Removal of outer door panel requires removal of two screws from inside the top of the door assembly at the latch, as well as all of the obvious mating screws from around the perimeter of the inside of the door assembly. Use a #15 torx driver bit. Pull top of panel out (away from the machine) by maybe two inches, then lift the outer panel up to clear the bottom end of it from the lower positioning brackets. DO NOT lever the top of the panel outward. Keep it close to the inner door. It may take bit of an upward tug to dislodge. Careful here - the outer panel will simply fall free. Two wire pigtails that are connected to components on the inner door are short, so be careful not to strain them after dislodging the outer panel. One is connected to the dispenser. Disconnect both as to provide good clearance for the component replacement. The main wire harness is of sufficient length as to not cause a problem. The six 3/16 hex head screws holding the dispenser in place are easy to remove. There are two small sheet metal tabs that keep the device in place after the screws are removed, but a rectangular mounting frame or bezel will come off, along with the little black curtain that protects the unit. The tabs are at upper left and lower right at the perimeter of the opening in the inner panel. They must be levered gently as to allow the dispenser to push inward for removal. After removal, spend some time cleaning the inner surface of the inner panel as to ensure that the new device will make a watertight contact when fastened in place. Bend the tabs slightly back to an inward position, and install the new dispenser with the socket and motor to your left as you look at it from outside the machine. It clicks in to place and stays put. The bezel mounts only one way (in terms of being upside down) and the flat surface must be toward the inner door. Re-positioning the little black curtain is tricky but if you follow the marks in the material from the previous mount it should work out OK. Tighten the screws evenly as to ensure a good seal. Move the outer cover closer and reconnect the two plugs. Use an object to wedge the inner door open by a few inches, and lift the front panel such that you can position it and slide it back down on the inner panel as to re-engage the lower holding brackets. This keeps the bottom of the panel in place during the reassembly. Now for the fun part... The upper end of the outer panel has to be positioned just right against the inner panel in order to seat the two long screws that straddle the latch assembly from the inside. You'll need clamps, or two people. There's a flat rubber seal on the top edge of the inner door. See that it is seated properly, and then that it becomes covered by the outer panel. If one person firmly holds the panels precisely in position, then the other person can install the screws to a point of being mildly snug. The other two longer screws go in the top-most holes at the upper/outer corners of the door assembly. Place them next. From there, you can carefully replace all the rest of the screws. Only after all of the screws are in place should you make all of them tight. You're done.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!

PartSelect found just the cap I needed at a much better price.

Fantastic service. Shipping was faster than promised. I can't say enough good things about them!

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

put new hose on, very easy.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

Snapped the new stops on. It took about 2 minutes.

Took out old rack by twisting the rack supports. Used old supports because in good shape. Removed the wand from old rack and placed on new rack. Then replaced the supports. Worked great.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

removed rack
removed one screw
removed old seal
installed new seal
installed screw

I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)