ACM2160AB - Instructions

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

Had a Trim Kit to remove, just 2 screws on the front to pull it out. Had to remove the tamperproof screws on the back (the outer shell is held on by them). I had to goto a local hardware store as nothing anywhere mentioned I needed this special tool (NOTE!!!!!!!) The bottom had normal phillips head screws. Note: I did not take the entire shell off, just bent it enough so the base plate could be pulled out. This exposed the motor, which strangely enough is NOT held in by any screws, just notches it slides in. Took the old motor out, came out VERY easily (only 1 plug to pull out). The new motors flange tab was bent a little bit so I had to use pliers to bend it back flat so it would fit in the notch on the bottom of the microwave (very easy). Overall A bit difficult due to special tool needed 9at least for me)

remove outer cover of microwave, (special recessed star bit required) change bulb, unplug and remove 1 phillips screw.

Note: also had to replace turntable. Removed top cover using secure driver set. Placed microwave on it's front, using a soft towel. Removed edge screws from bottom plate (leaving 4 screws in center attached to heavy transformer). Separated bottom plate from body of microwave (leaving transformer wires still attached) exposing Synchronous motor. Removed two screws holding motor and electrical plug. Swapped new motor in its place. Re-attached bottom plate with its screws. Placed microwave onto it normal position. Re-attached top cover with its secure screws. Installed new turntable inside.

Removed each switch (3) and checked them with multi-meter; got intermittent readings on two of the three. Also broke of a piece of the frame that holds the switches trying to remove them (old, exposed to heat and moisture over the years caused the plastic to become brittle and the wiring connectors were also hard to disconnect probably because of heat and moisture over the years).
Went to PartSelect web site and discovered the three switches and frame were bundled in to one part number, 43501A. So, I called and spoke with a very knowledgeable technician and she explained why plus helped me order the part over the phone. When I received the part, the switches were already mounted in the frame and the frame was modified compared to the OEM frame. As I began to remove the old frame, I discovered why the new frame was modified. It was as if PartSelect had done many of these door interlock repairs and they knew exactly where and how to modify the frame and communicated this with the manufacturer, because the new frame installation was very easy, there was nothing hard about installing the new frame with the switches already in place. I then reconnected the wiring to the switches and tested the microwave and it works fine now, Problem solved, Thanks PartSelect.com

Removed case,
Discharged HV capacitor and removed cooling fan.
Unscrewed ground end of HV diode and unplugged from HV capacitor.
Installed new diode by reversing the order. In my case, the problem was the magnetron was bad, so I replaced it as well.

Took the cover off, had a lot of screws but easy. Removed the old motor and inserted the new motor. Replace the metal cover and it was ready to go. Can't believe I have waited so long to do this. I was going to replace the microwave but could not find the correct size to fit the cabinet.

I could just set the new whirly gig in the bottom hole of the micro and it worked. The new part was delivered in 24 hours of my order and hence fixed in 24 hours. Thanks so much Part Select

I took the turntable roller guide, dropped it into the hole, put the plate back on the turntable roller guide; and voila!!! It worked!

Took out the old, put in the new.

Initially we started looking to buy a replacement microwave to replace our 13+ year old built-in microwave. It was a real pain finding a replacement to fit the exact dimensions. So I thought I'd try to find an old KitchenAid microwave. However, I was pleasantly surprised when this site came up on my search. Their website allows me to input the problems and then it showed two possible parts that needed to be replaced. I emailed tech support and asked them which part I needed. They responded very quickly and said I needed to replace the magnetron. I watched a couple YouTube videos and then pulled my microwave apart. It was incredibly easy to pull the outer cover off. The magnetron had 5 screws that needed to be removed and one electrical plug. Took me maybe 10 min to complete the entire repair. It was one of the easiest repairs I've done and so thankful for this site They saved me a ton of money from not buying a new microwave and we now have our microwave working again. In hindsight, I wouldn't hesitate. I'd order the Part now and get it fixed.

Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.

well I unplugged the microwave one day prior to working on it. shock precaution smart way to do this job. very easy pullout the screws behind the unit pull off the outer casing. minor screws inside the unit you have to remove a couple things out of the way. unplug the magnetron and remove first gives you more room to work on the side panel to replace the micro switches. I only replaced one the bottom micro switch. only one bad, but since I was in there I clean the bulb and changed the magnetron any ways. I read other reviews and made my choice to do so. it works perfectly now. Thanks PartSelect for having parts.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.