ACG130NCD0 Frigidaire Refrigerator - Instructions

unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works

Pulled the few end caps off the retainer bars, pushed the new ones in, and used a medium hand strike to seat the end caps in the doors slots.

the repair went fast and easy. my boyfried measured the retainer bar, cut it with the hack saw installed the right and left side door shelf end cap and inserted the door shelf retain bar. the door looks great. would highly recommend your website and customer service. thanks again.

The replacement part was a bit too long (about 6"). Measured length of the existing bar that was on lower shelf and used a rotary tool with a metal cutting disc to make the same length. Everything snapped into place easily.

Needed to saw the pieces. PUrchased hacksaw.
Son sawed the pieces. Went in like a piece of cake.

I replaced the shelf end caps in the shelves of my fridge and I also replaced the gasket around the door.

Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.


Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!

I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.

First I removed the broken end caps. I placed the new end cap onto the shelf bar and snapped the end cap into the holding slot on the door interior. Took about 5 minutes. Very easy.

We have a wonderful Kelvinator refrigerator. It has served us tirelessly for more than 15 years - and looks as good as new! (We frequently clean it out and clean the interior and exterior, to keep it looking and smelling clean)

Replacement of the end caps and shelf was very easy!

The broken end caps were removed (missing for years), and it became one of those small projects that one never gets around to. I finally took down the model number and looked online for it. Google or Yahoo (can't remember which) pointed us to you site. I was SHOCKED to see that the parts were still available! I called your friendly customer order line and had a very pleasant experience placing the order. The BIGGEST shock came when the parts arrived THE NEXT DAY!! Just in time for Thanksgiving! You are AWESOME!

The Repair:

Easy as pie. The end caps simply snap into place. I did the left side first, then carefully inserted the metal bar, which is supported by the two end caps. Next I snapped in the right side cap - DONE. It took longer to clean the bar up, than it did to replace the caps!

The Results:

The bottom door shelf is now useable again. We can place 2 liter beverages and juice containers on the door, where they belong! My wife cheered and commented, "The refrigerator is no longer an eye sore when I open it!" :-)

Thank you Parts Select!!!!

I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.

replaced it

I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.

It snapped in place.

Door panel was already off. Took off broken caps, placed new ones on & put back on door.

I removed the broken end caps by hand. They snap in to the center retainer bar. I ordered replacement parts from part select on their website. New end caps arrived in a couple of days. I installed new caps. No tools needed. Great service by part select. Thank you tm staten island ny