ACF7225AW Amana Range - Instructions

Purchased 2 piece broiler pan from this site

I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "labor".

1. Flip "OFF" circuit breaker.
2. Pull out range unit from wall.
3. Unplug range unit.
4. On the back of the range unit, remove 4 screws holding lower rear cover using a phillips head screwdriver.
5. Remove lower rear cover.
6. Unplug temperature sensor connector (1 wire connector located upper right section behind oven).
7. From inside oven (upper left, back corner), remove 2 screws holding temperature sensor unit using a Phillips head screwdriver.
8. Remove old temperature sensor unit.
9. Insert new temperature sensor unit (wire connector end first) through opening and secure reusing old screws.
10. Re-connect temperature sensor connector.
11. Re-attach and secure lower rear cover reusing 4 old screws.
12. Plug in range unit.
13. Move range unit back to desired location.
14. Flip "ON" circuit breaker.

I just got on youtube, typed in "replacing hinges on an amana oven door" and an awesome video popped up. The job was a cinch.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

This was very easy to install. I removed the screws that held the trim in and took it off and put the new one on and screwed it on. Within 5 minutes it was complete. I just wanted to say that my wife was very discouraged because she couldnt get the discoloration off the trim. So she went on the internet and found partsselect.com. I gave here the model number and from there it was easy to find the part and order it. Within 5 days we had the part delivered and installed. Thank you because it was so easy.

A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like clockwork. I would definitely order in the future. Thank you.

The front burner the large one was burnt out, I cook alot so I need it, I happen to see a appliance repair man next door. I describe problem and he said well figure about 250 - 300 hundred dollars. 80 For the aprt the rest labor and house call. Well I looked at the booklet and figured out what I had to do ,needless to say I owent to your website and you had the exact part I needed and saved me alot of money. I sugest to d. I. Yers try it and if it doesn't work then call the repairman. Thank you parts select. Glenn voight

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

First I had a repairman come out. He stated it was the latch that went bad. After 2 weeks I found out it was not covered by the home warranty and he still has not got the part. He told me it would take 2 hours to replace and cost me 200 dollars. I ordered the part and had it here the next day. I found out it was a lot cheaper to do it myself.

Remove three screws underneath bottom front edge of the range top. Bewteen the oven door and the range top. Lift rnage top up in frotn and prop up. Remove two screws o the element and replace. Found out the problems was not the element but the control switch. The heating element for the bimetalic control was brokened and not making contact. Element was ok. Would advise inspecting and using a dvm to check resistance of the element before purchasiing. By the way I swapped the control switch from another element and found out that they are claibrated to the sixe of the element. You have to purchase the right control switch or the element will not heat correctly.