Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AAV8000AWW > Instructions

AAV8000AWW Admiral Washer - Instructions

All installation instructions for AAV8000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AAV8000AWW
271-285 of 465
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

very loud screeching noise when washer was rinsing/ spinning

  • Customer: SANDRA from PASADENA, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
remove small panel on backside of washer, 3 screws. removed both intake and out take hoses on pump, clamps only. removed screws holding pump in place,2 i think. removed old pump replaced with new pump.attached both intake and outtake hoses with same clamps.Finished with pump installment. removed old belt by loosening the motor pully and slipping the belt off. placed new belt on pully and drum mechanism. tightened the belt to proper tension. ran a short cycle to ensure working condition then replace back panel.

Water on floor under washer. Took off small back cover, squeezed hose, water dripped out. Removed hose and found split in hose.

  • Customer: David from Lexington, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Used pliers to remove spring clamps on either end of hose. Removed hose. Put clamps on end of new hose. Slipped hose ends in place and re-secured with clamps. Another save by PartSelect!

Banging, maching "walking" in spin cycle

  • Customer: Bob from Charlottesville, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Posted instructions/videos were on the mark.
Some springs are more difficult to reach, so disconnecting the entire cabinet from the base to gain access from different angles helps a lot to connect/disconnect the springs.

Drain hose leaking

  • Customer: James from Westminster, CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched videos on how to replace the hose. Armed with the information I started the process. But the videos were wrong. After removing a bunch of screws and not getting to the hose I removed the inspection panel on the rear,three screws and there was the hose.simple. I wished I had not watched the videos.

Washer would shake and move when spin cycle on.

  • Customer: Mark from Phoenix, AZ
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I remove the necessary panels, hoses and electrical section and removed the tub springs and pulled the tub assembly out of the unit and replace the snubber ring. Was really not hard to do and it worked like a charm. No more problems :)

High pitch screech when rinsing

  • Customer: Michael from Punta Gorda, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First thing was to go to PartSelect website to see what others with the same problem did to solve their problem. It was 45% pump and a lot less for the belt. My belt is only a year old so that was out. I ordered my new pump and watched the video on PartSelect a couple of times. I didn't bother to disconnect the water and drain lines. I had my wife hold a plastic 2 quart container under the pump when I pulled the small hose off and didn't spill a drop. Like the man on the video said...the new pump isn't identical but it fits and works fine. Thankx PartSelect!

Motor Burned Out

  • Customer: BArbara from Freeport, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the front panel off the washer with a screwdriver, tilted the washer back and propped it up with a paint can, unscrewed 2 nuts & bolts, disconnected the electric to the motor and lifted out, put the new motor in place & secured it with the nuts & bolts, reconnected the electric and re-installed the front panel of the machine and I was done.

changed water pump

  • Customer: Joseph from dowagiac, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
very easy repair, acess from the back, just a 1/2 dozen screws to change

agitator came off while spinning

  • Customer: Claudette from Monument Beach, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy to replace. Just wish they would have suggested to order the screw as well at the same time.

machine spin cycle not working

  • Customer: Brian from Lewiston, ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
placed washer on front exposing bottom of machine. removed clip holding pulley in place with needle nose pliers. The old parts slid off transmission shaft easily. I set these aside in order of removal. The replacement parts were not exact matches to OEM parts replacement bearing was heavier duty and thicker there were washers in the kit that would not even slid onto transmission shaft,replacement pulley and cam were exact replacements for OEM. I replaced the bearing and thrust washer and then used a combination of new and old washers to build the assembly back to the original length so the retaining clip would hold assembly firmly in place.The instructions key point was that the final height had to bring the pulley back to the original height for a snug fit with retaining clip. Once I realized this the extra parts in the kit were less worrisome.

Making knocking noise when win wash cycle

  • Customer: Paul from Tyler, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I replaced both the belt (PS2018741) and water pump (PS2347193)on my Maytag Washer MAVT446AWW. I replaced the belt and water pump at the same time because my machine was making a pretty loud knocking noise (like a belt was flapping loose -- but the old belt was not broken. I used the instructions in the PartSelect.com video and installation was pretty easy. Both the new belt and water pump work fine. BUT the knocking noise in the wash cycle is still there. Does anyone have a suggestion on what I can check next with regard to this problem? Thanks

shaking & walking

  • Customer: fernando from lockport, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
i had a hard time installing springs. also it didn't fix the problem. is there another problem i have to fix so it stops shaking & walking. if so what is it ?. do you have a tool to install the spring ?.

water pump stoped working

  • Customer: donald from fillmore, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Easy fix. I pulled the washer out from the wall and leaned the top back to the wall. I then removed the belt from the bottom. I set the washer back on all fours and slide it around so I could get to the back water pump access panel. Using a nut driver, I removed the screws from the panel, then I removed the panel. I could now see the water pump. With a pair of pliers I removed the two hose clamps, and removed the end of the hose's from the pump. Then with a socket wrench I removed the three screws holding the pump down and removed the pump. In reverse order I put it back together. It works fine and saved me a lot of money from happened to buy a new washer. Thanks PartSelect.

Noisy spin cycle

  • Customer: William from Cochiti Lake, NM
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Just as shown in video on website

vibration durring spin cycle

  • Customer: jennifer from dwight, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
follow the video on snubber ring replacement an use 1/2 inch washers keep the tub springs from collapsing then it is very easy to remove them make sure to tilt the tube assembly an un hook start to finish under 1 hour
All Instructions for the AAV8000AWW
271-285 of 465