Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AAV1000AWW > Parts

AAV1000AWW Admiral Washer - Parts

All parts for the Admiral Washer AAV1000AWW

Below is a list of all parts for the Admiral Washer AAV1000AWW - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the AAV1000AWW
1-14 of 135
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.34

Suspension Spring

This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.

$4.42

Lid Hinge

The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hinge. This lid hinge is an inch and a half long, all white in color, and it is made entirely of plastic. To complete this repair, you will need a Phillips screwdriver and a putty knife to remove the top of the washer, in order to access the screws that hold the lid hinge in place. Be sure to disconnect the power to the washing machine before beginning this repair.

$5.26

Snubber Ring

The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the ...

$9.41

Lid Hinge Pin

This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plastic. This lid hinge pin is just over an inch long, is sold individually, and does not include the mounting screw (consider ordering mounting screw if it rusted or stripped). It is recommended to check the opposite lid hinge pin before ordering because hinges may wear at the same rate. Be sure to not tighten the mounting screw to pin too tightly to avoid breaking the new part.

$52.97

Transmission Pulley and Bearing Kit

This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, an...

$72.17

Drain Pump with Pulley

This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is activated after the spin speed has been maintained for a specific period of time and is driven by the same drive belt that also runs the transmission pulley. If your washer is not draining properly the pump could be clogged by a small object or could be broken and in need of replacing. Tools you will need for this repair include a 5/16 nut driver, a putty knife, a 3/8 socket with a ratchet, and a pair of slip joint pliers.

$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$2.96

Cover Screw

Sold individually.

$136.02

Motor with Pulley

This motor is a 2 speed, 1/2 HP, 120V, 60Hz.

$17.59

Tub to Pump Hose

Hoses are the most likely cause of clothes washer leaks. This tub-to-pump hose carries the water from the tub to the drain pump. If you notice that your tub is leaking during the wash cycle, check the the hose for holes. If the tube does have a hole or crack in it, the part should be replaced. Also, check both the connection and the juncture of the hose with the drain for your house. While you are looking at the hose, check to see if the threads or clamps are corroded or loose. This OEM replacement pump hose is 20 inches long, and fits most clothes washer units. Remember to turn off the water supply and disconnect the power from your washer before you begin this repair.

$4.63

Motor Pivot Spring

$5.05

Screw

This screw is less than an inch long. It is a metallic screw that is used for many clothes washers.

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...

$8.93

Leveling Leg and Pad

This leveling leg, which includes a lock nut and a pad, is used to keep washing machines still and balanced. If your washer shakes and moves excessively, then this could be an easy and quick solution to your washers problem. To install, the damaged pulley must be removed to install new pulley. The suggested tools are pliers, a socket set, and/or screwdrivers. For safety precautions, make sure to unplug washer from power source or shut off the house circuit breaker. Remember to wear gloves prior to starting this installation project. Refer to the instructional diagram provided by the manufacturer for further guidance. Customers suggested the detailed diagram as helpful.

All Parts for the AAV1000AWW
1-14 of 135