Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AAV1000AWW > Instructions

AAV1000AWW Admiral Washer - Instructions

All installation instructions for AAV1000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AAV1000AWW
271-285 of 357
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

vibration durring spin cycle

  • Customer: jennifer from dwight, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
follow the video on snubber ring replacement an use 1/2 inch washers keep the tub springs from collapsing then it is very easy to remove them make sure to tilt the tube assembly an un hook start to finish under 1 hour

Pump was leaking water on the bottom

  • Customer: Yevgeniy from Monroe, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I did it just like a video was showing. This was really good instructional video.

Bad Water pump

  • Customer: Robert from bridgeton, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Tilt washer back and pop belt on bottom of washer. Use putty knife to open top of washer 2 clips 2 inches in from both sides. Use racket to open and remove front panel of washer. use racket to remove 3 screws that hold pump to base of washer. pliers to remove clamps for intake and output hoses. use small bucket to catch water in hoses and pump. Replace pump unit, put screws in, put pump clamps on, put front panel back on , snap down top of unit, put belt back on pulleys and your done.

Washing machine made a strange loud noise and then would not drain.

  • Customer: Dermot from Coral Springs, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The video on PartSelect.com regarding replacing the washer machines drain pump with pulley was extremely helpful. By following the simple instructions as shown in the video, I was successful in replacing my washing machines pump in less than an hour, and saved myself the labor costs a repairman would have charged me for a really simple and easy repair job. I was also extremely happy and impressed with PartSelect.com. The price I paid for the part was very competitive and arrived within 3 days. I was very glad to see the pump and pulley assembly was a Whirlpool factory certified part and not a knock-off or reconditioned part.

loud metal on metal sound during spin cycle

  • Customer: Shane from Mobile, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed write ups on this web site and the job was straight forward. As far as the washer brake rotor I did not need to replace it. After removing the six screws that cover the assembly I noticed some rust and dirt so cleaned it with degreaser and reassembled it. I have no loud screeching sounds when the spin cycle comes to an end. As always PartSelect did a great job getting the correct parts to me with in a few days, thanks.

Noisy during wash cycle and spin

  • Customer: Phil from Winfield, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removing and replacing the pump was a very easy process. Once the belt was removed on the bottom of the machine, I removed the back plate to gain access to the pump. Three screws and a couple of clamps holding the hoses on the pump. There was a little more water in the pump during removal than anticipated. Other than that, it was an easy fix.

Hinges for the lid were broken

  • Customer: David from Chandler, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went smoothly with no issues or problems. The video link sent with the receipt made all the difference in the world. I watched the video on my iPad as I was doing the repair. Also locating the parts I needed on the part select website could not have been simpler.

Lid on washmachine was loose. Found that one of the plastic hinge pins had broken.

  • Customer: Larry from Woodbury, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered two new hinge pins as well as hinges. (Did not want to have to deal with it again so chose a full change out.) Watched a U-Tube video that described how to change out the hinges. The trick is find out how to lift the top panel on the washer to access the screws that anchor the hinges. Use a putty knife and slide it into the space between the top panel and the front panel. Got the job done today in an hour or so. Chose to also wipe out the top of the wash tub at the same time so it took a bit longer. Works fine now. Just like new.

Lid Would Not Stay Up

  • Customer: michael from blanchester, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took of lid,took out screws,put on hinge and pins,simple job

A periodic loud noise during the Spin cycles

  • Customer: Randy from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
This is a quick and easy repair. Start by using the putty kiife to depress and unlock the washer top. Remove the front panel of the washer by removing the two screws on eithe side at the top. The front panel then lifts off. Next you will want to tilt the unit up and remove the fan belt. Put the washer back down flush and remove the hoses to the drain pump located at the front an right side of the bottom plate. Once the hoses are removed you can remove the three retnetion screws, take the pump out, put the new pump in and fianlly replace the rentention screws and hoses. Put everything back together in reverse order and don't forget the fan belt. Takes all of 15 minutes of your time and you save 150 dollars labor.

Lid hinge pin broke

  • Customer: Paul from Antioch, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The videos included in the shipping notification email made the repair a breeze. The only thing not shown was (at least on my washer) that the screws that needed to be removed had torex heads instead of normal slot or phillips heads. Luckily my tool crib had what I needed.

mouse ate hole in tub to pump hose!

  • Customer: Robert from Chapin, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Slip wire clamps over tube ends. push hose ends over connections, move clamps over hose end, making sure clamps are centered on connections. Easy as could be.

Loud screech at end of each cycle and knocking sound from bearings going out.

  • Customer: Don from Osceola, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Tipped washer backwards and removed belt from all three pulleys. Stood washer upright again and removed back panel around pump(4-screws)Removed drain hose from house drain and emptied excess water in the pump into a bucket. Removed the hoses from the drain pump then removed the three bolts holding the pump in place. Removed damaged pump and replaced with new drain pump. Reassembled in reverse order. Once the pump cover was replaced, tipped machine on its back, replaced the belt onto the three pulleys and promptly returned machine to its upright position and ran a test load of laundry! Success! Works great!

In spin cycle, made a loud nosie

  • Customer: Vicki from Pollard, AR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Took the back off, located problem, ordered part, removed old part, installed new one, tilled washer to put belt back on. Whole process not bad at all. Working with this site was so very helpful, will keep in in my favorites or future use. Thank You Parts Select!

change out pump bearing wore out

  • Customer: Bennett from russiaville, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unhook water lines after shutting off water, unplug power cord.Then move washer out into open space for easy access. Used flat tip driver to push in the spring clip to open the top of washer. Flip top up and had wife tilt the washer back. Once bottom is exposed took belt off the motor pulley. Let washer back down. Use the socket wrench to take out two ( front corners ) screws. Tilt front panel back and lift out off the clips . Water pump is front right corner. Use socket wrench to take out the three screws that form a triangle. Lift out the pump. Have something to catch water from pump . Use pliers to remove the two clamps spring from the hoses . Remove both hose from the pump. Then install new pump in the reverse order and close up washer in reverse order and put belt on . Replace washer in it place reinstall water line and lastly the power cord needs tobe pulg in. Now test the washer.
All Instructions for the AAV1000AWW
271-285 of 357