Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A9895XRB > Instructions

A9895XRB Admiral Microwave Oven Combo - Instructions

All installation instructions for A9895XRB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave oven combo repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the A9895XRB
91-105 of 139
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F1 Fault Code - Replace the Temperature Sensor

  • Customer: Dennis from Tampa, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

Light lens broke when self clean cycle was used

  • Customer: James from Buford, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Light burned out in upper oven

  • Customer: Shirley from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

My oven was not holding temperature.

  • Customer: Anthony from Acworth, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

Upper oven shut down after reaching temperature

  • Customer: Earl from Globe, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Bulb Replacement

  • Customer: Judith from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat

  • Customer: DAVID from Cape Coral, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

change oven sensor

  • Customer: Lloyd from Eau Claire, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed provided video

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington, NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Oven have F2 and F3 codes following cleaning cycle making oven inoperable

  • Customer: Timothy from Longmeadow, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

Damaged the oven lamp socket while removing a broken bulb.

  • Customer: Ronald from Dover, DE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Upon receiving the replacement part, I noted that the socket was held in place by simple expanding tabs. TURN OFF POWER TO THE OVEN. Using a right angle pick or similar tool, bend the tabs inward on the existing socket and remove. Disconnect the white, black and green wires. Note which tab is the green tab. Attach the wires to the new socket. Push the new socket into place, aligning the key bump on the socket with he slot in the oven wall opening. Install bulb and diffuser.

Range had an F-2 code on the control panel

  • Customer: Greg from Frederick, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Oven would overheat

  • Customer: MARK from roseville, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

Broken plastic knob

  • Customer: Judy from McKinney, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Placed new knob directly on post. No problem
All Instructions for the A9895XRB
91-105 of 139