A9400W Maytag Washer - Instructions

Occasional noted leak became worse and I had a repair service out. Incorrect detection of outer tub seal made so cancelled them and read comments about raising the top. Did so just at start of a rinse cycle to see soapy water shoot from top of syphon break then continue to dribble out through tub empty process--this is what had cause the water to flow down the interior drain hose and out through the side and bottom near the pump.

Ordered all the parts shown here and they arrived just in time for planned work. Did not need or use the clamp and gasket purchased as the gasket was included in the break package and I really like the old-style clamps much better.

Replaced the break and the elbow and put it back together. Things went south on a rinse as water shot out the back hose at the new elbow. I had not realized the size of the new elbow was smaller than the original. Went back to the old elbow but it bothered me that it would still move when the 4 assembly bolt-screws were completely tight.

So far this seems to have worked. There does not seem to be any leaking at all. For those who read this, the job could be done in about and hour for less than I spent if you observe and diagnose properly. It appears that the washer at the end of the Syphon Break wore out and that is what caused the leak.

Thanks much to PartSelect for being in business and to all the posters on this site for helping everyone to get these things done right!

Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years!

Placed a towel on top of the washer.

Using a flat screwdriver, carefully removed black plastic cap from inside the dial. Gently lifted and slid out the small gizmo that held the timer knob onto the front of the washer. Laid the black cap, timer knob, and small gizmo on the towel.

Using a phillips screwdriver, unscrewed the 4 screws holding the front panel. Set the screws on the towel. Placed the front panel face down on the towel.

Removed the old timer by sliding out the three flat pieces that were part of the black coated wires that were attached to the old timer(two top and one underneath). They were hard to detach. Unscrewed the two screws that held the old timer in place. Set the old timer aside.

Replaced the new timer in the same manner as the old one came off. Slid on the three flat pieces, then screwed the timer on. Lifted the front panel and screwed it tightly. Put the timer knob back on and clipped the gizmo to hold it in place. Replaced the black plastic cap.

Discarded the old timer and kept the instructions for future replacements.

Followed your directions and it went very easy.
Only took maybe 30 mins.
I was impressed with your trouble shooting and inst!!!!

Thanks

wayne

First I removed the screws that held the side panels on at the bottom, then I removed the screws that held the front panel on and removed the panel. I removed the agitator, loosened the retaining nut with a hammer and a punch, removed the bolts holding the tub springs, removed the bolts for the top panel and flipped it out of the way. Then I removed the clamp for the inner tub and pulled it out, then I pulled the outer tub out. Then I removed the seal and scrubbed the rust off the seal mating area, then installed the new seal and re-assembled the washer. It works perfectly now and no longer leaks and it is over 20 years old. This is the first bit of problem we have had out of this machine, the lonely Maytag repairman commercials are true.

I loosened three screws to relieve the belt tension and removed the belt from the pump drive pulley. After removing the water from the wash tub I removed the intake and output hoses from the pump. I next removed the mounting screws and removed the pump. I attached the new pump loosely and re-attached the belt. I moved the pump to tighten the belt tension and tightened the mounting screws. I re-attached the hoses, filled with water, checked for leaks and replaced the front panel.

This was a pretty simple repair. In this case, the part purchased here was not the actual problem, but had to be disturbed to fix another problem. After many years, corrosion and exhaustion of grease caused the bushing on the agitator shaft to seize, and the belts to slip. In this model machine, the bushing is accessed by first removing the agitator, which is held on by a single 1/4 inch set screw, and then removing the agitator seal, which is held in by a little spring clip on top of a washer. It's soft rubber, and you will probably need a small screwdriver or pocket knife to pry it out. In this case, the bushing was not too bad, so I was able to clean the hardened grease out and free it up with a little oil, using vise grips to rotate the agitator shaft, until the oil worked in enough.

Since seals don't like to be disturbed and reinstalled, and this one requires some prying to get out, I bought a new seal, even though the old one did not leak when I temporarily reinstalled it. There is a spring inside the seal, and it is packed with grease. The new seal comes with the spring and the grease already in it, so all that is needed is to slip it over the shaft (the top has some print embossed on it, making it easy to remember which is the top), press the washer down on top of it, and replace the spring clip.Slip the agitator back on its shaft and retighten the set screw, and you're back in business.

Run the machine, and check the area where the transmission enters the bottom of the tub. There's a little weep hole there, and if the seal leaks, you'll see water coming out there.

I moved wash machine away from wall and unplugged from wall outlet. Shut off water, then removed hot and cold water lines from water inlet valve,removed screw from mounting plate and removed valve from wash machine. Checked to see if replacement valve was compatible (exact fit).
Unscrewed the two screws holding valve to mounting plate,unscrewed hose clamp and removed water line at top of valve (outlet). Removed the four wires from solinoids.Replaced the four wires onto the new valve as they were on the old valve,reattached water line onto the top of valve and tightened.Reattached valve to mount plate with the two screws and mounted back onto machine. Hooked up hot and cold water lines back onto valve and snugged with pliers. Turned on water checked for leaks (no leaks), and did a load of laundry. Super simple,well worth doing yourself.

Pryed the front cover off and set it aside. I pulled the top cover off by removing the 1/2" hex screws under the front cover and hinged it back. Removed the agitator set screw with a 1/4" hex nut driver and pulled out the agitator assembly. Had to remove the nut that holds the hub assembly in by using a hammer and punch. There is not much room in the tub so be careful you don't hit the sides. It goes off by turning it clockwise. Then the splash guard comes off and then the inner tub with the top gasket and ring can be lifted out of the washer. The tapered cork covered hub was exposed and it also had to be removed with a hammer and punch clockwise after removing the torx set screw on the side of the hub. The rubber seal was now able to be removed under the hub and on top of the bearing on the outer tub. I had to clean all the accumulated scale off seal and bearing surfaces before putting new parts in (rubber seal, hub assembly, and new locking nut). Everything went back easily. Should be good for another 5-10 years...

The washer would either stop too soon or advance too slowly through the cycle. I ordered a new timer motor. It was so easy to install that I did it while I was on hold on the phone. Removed four screws on top to open the front panel. Two screws holding the motor and two wires for the timer. That was it! Put it all back together and it works fine now.
Our old Maytag washer has a new life!

removed face of washer and replaced belts. The only problem I had was didn't own any torx security drivers.

The job went fast an well

Water was leaking at the injector nozzle during the fill cycle. I could not visually see any damage to the existing part, but, ordered replacement parts, anyway. The new parts arrived and looked EXACTLY like the old ones. Clearly, the new parts would leak, too. So, I cut a three-inch length of 3/4-inch OD pipe and spliced the two hoses together, completely eliminating the troublesome parts. The washer works fine and does not leak. And, it fills much faster, now. I still have no clue as to the purpose of the injector nozzle nor do I know why it did NOT leak for 30 years.

The motor was easy to replace: unplug the wiring harness, slip off the belts, release the tension springs from the motor carriage with needle-nose pliers, and then unbolt the motor carriage with socket set and remove from the washer. Remove the pulley from the old motor with allen wrench and transfer the carriage to the new motor. Reverse operation for everything and you are back in business. The hardest part was the far back screw holding the carriage, a wobble extension helped.

First, I secured one lid hinge ball in its appropriate position between the lid and the washer. While keeping the first ball in place I placed the other lid hinge ball as close to its intended position as I could get it. Next, I pushed the lid and ball into its position.