Models > A8610PA > Instructions

A8610PA Admiral Cooktop - Instructions

All Instructions for the A8610PA
46 - 58 of 58
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Need new Surface Burner Knobs
Just pulled the old off and pushed the new ones on.
Parts Used:
Infinite Switch Knob
  • Robert from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old dirty drip pans
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Parts Used:
Chrome Drip Bowl - 8 inch
  • gizella from mays landing, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner did not heat
New receptacle element. I am a girl and I did it.!!!!
Parts Used:
Surface Burner Receptacle Kit
  • lula from Antelope, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Parts Used:
Surface Burner Receptacle Kit
  • Darwin from wisconsin rapids, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Two old Surface Burner Receptacles needed to be replaced.
I followed the instructions given on your great site. Thank you so much.
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch Surface Burner Receptacle Kit
  • Willis from Anaheim, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip bowls tarnished.
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".
Parts Used:
Chrome Drip Bowl - 8 inch
  • Jennifer from Albion, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Dirty drip bowl
Remove old drip bowl from the range and put a new one back.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Paul from Carnegie, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
unable to remove screw with screwdriver
used drill to remove old screw
Parts Used:
Surface Burner Receptacle Kit
  • Emmett from Rayville, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I wanted to purchase new drip pans, since those that I have are a bit grimy
I will begin by saying that not only will I continue to order my parts from PartsSelect, but I also highly recommend this business. If you call Whirlpool be careful that they forward your call for parts to some preferred vendor, which a customer might assume is Whirlpool but it is not. PartsSelect is the same type of business, but with outstanding customer service. With regard to the drip pan, Whirlpool had not updated the part number for these as I found out when i called them. Whirlpool no longer uses the drip pans without the holes which is a serious problem since this could be hazardous to the owners of these ranges if you are forced to purchase the drip pans with the holes in them. That said, I ended up keeping my old drip pans, because if you spill grease under the new ones with the holes in them and since the range design with the fan built in on the top does not allow you to lift the top to clean under the pans, you could end up with a grease fire. This is not the fault of PartsSelect and they handled my order in a manner that I would give them a rating of exceptional for customer service.
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch
  • Hedy from Richmond, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Cartridge wire burned out
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Parts Used:
Surface Burner Receptacle Kit
  • Robert from San Francisco, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The surface burner element burned out on my 20 year old Jenn Air electric stove.
It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major
Parts Used:
Surface Burner Element - 8 Inch
  • Wanda from Riverton, WY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner coil was falling apart.
Used new plug in coil burner.
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch
  • Mary Kay from North Charleston, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the old bowls were burned.
really easy.
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • Rosibel from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the A8610PA
46 - 58 of 58
Back to Top