A68HK-6TXW-R Admiral Range - Instructions

Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

slide stove out unplugged it took six screws out put new one in transfered wires pluged back in and it works thank you

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I first removed the back panel that covers the switches from back of stove; then I removed the wires and put them on the same numbered wires on the new switch; put the new switch in place with the wires connected to it; installed the 2 front screws and put the back cover on again & it took about 10 min and saved about $300.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.