This helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not drain
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Jenn-Air, International.
Part# WP6-2008160 replaces these:
200816
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noise from dryer in spin cycle,
Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!
curtis from ROCKDALE, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water didn't pump out during the spin cycle
I took out the two screws in the bottom front panel of the washer, and rotated the front panel from the bottom away from the machine until the top or the panel was released from the machine frame. I then tilted the washer back to get access to the bottom of the machine. The pump pulley had split in half, and the bottom half fell off the d
... Read morerive motor shaft. The only problem I had was breaking free the set screw that holds the pulley to the drive motor shaft. I used a long arm Allen wrench and an adjustable "Cresent" wrench to apply enough force to break the set screw loose. Iclamped the upper transmission belts tightly to keep the motor shaft from turning while I loosened the set screw.
Read less
Robert from Menomonee Falls, WI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Wrench (Adjustable)
30 of 38 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washing machine ran noisily
Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Leve
... Read morel the machine.
Read less
Xuanbao from Norwalk, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
5 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no water drain
removed old pully, put new one on with hex driver, removed belts, put new belts on and finished.
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Oscar
February 14, 2019
My belt started smoking when spin cycle started. Could this be a bad pulley bad belt both which pulley usually goes bad
For model number Lat8406aae
Hi Oscar,
Thank you for your question. If you are getting a burning smell from your washer, you will need to check both the belt and the pulley to see which part is causing the issue. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jeff
May 15, 2019
What i assume is a clutch pulley on the very bottom of the motor shaft that drives the pump has worn out and fallen off. I need the part number so i can order a new one. Again this pulls drives the belt to the pump.
For model number A110
Hello Jeff, thank you for inquiring. This Motor Pulley for your model fits the description you are giving, but there is also the Transmission Drive Pulley part PS11743025 for your model that you may be referring to.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Gene Bosch
October 14, 2019
Motor making a buzzing sound, all the pullies seem to move freely. The belts seem to be in good shape, but when the machine is suppose to spin it does not nor does it drain water. I checked for hoses being plugged or something being stuck in the in the drum and found nothing. Does this washer need a motor or could it be something else?
For model number LAT9416AAE
Hi Gene, it is likely the motor is burned out and needs replacement. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Debra
October 7, 2022
I replaced the drive and pump belt on my washer. Now the motor pulley squeaks is it possible I tightened the belt too tight?
For model number LAT8204AAE
Hi Debra, thank you for reaching out. If your washer's motor pulley squeaks, ensure that you haven't overloaded the machine or gotten items stuck under the agitator. If a belt is too tight, it can add stress to your bearings. The added stress can produce noise. Once you rule those out, you can troubleshoot for dirty or damaged pulleys or a worn-out clutch assembly in the gear case. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Doug
September 14, 2017
Second time asking - recommended that we check the water pump. Disconnected the belt for the water pump and still had noise. We change belts, bearing and tub seal. Still having whining noise that comes from base of the unit. Possibly the motor or base?
For model number LAT2600AAE
Hi Doug,
Thank you for your question. Those parts could definitely be part of the issue but I would suggest checking the belt, tub bearing kit, glide and spring kit, and your damper pad kit as well. All of these parts would be physical, so you should be able to see if they have worn down. Good luck with your repair.
