A3875XRA Admiral Range - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wire and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.

I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

unplugged power took the back panel off unplugged the 5 wires removed knob by grabbing and pulling off took two screws out of front panel removed the switched put new switch in place and reversed the procedure went very smooth know problem at all any one with any kind of ability should change this switch in know time at all

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

Drop in range was in excellent condition until element burst and was getting ready to purchase another range and then I was looking to replace the element and found part select and they were great from the order process and shipping was fast and the whole process was 5 STARS. As far as me doing the repair I watched the video and it was simple for even me. I also replaced the bake element at the same time. Once again I highly recommend Part Select and they are second to none.

Pull out the range...hardest part.
Remove back panel.
Remove/install switch
PS,
This is second switch I had to replace. Try making them in the United States.

Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making my problem, no problem at all!

Everything was straightforward other than the tabs that the screws go through before going into the back of the oven were the wrong size and the predrilled holes were not in the right location. Had to trim the metal tabs and redrill the screw holes.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.