A3520SPN Admiral Range - Instructions

Donna from Dallas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

471 of 478 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowls needed to be replaced

took old bowls out, put new bowls in, took a coffee break

Parts Used:

John from Chester, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

453 of 542 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove top element not working due to bad receptacle.

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Parts Used:

Richard from Carthage, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

191 of 208 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old drip pans stained

Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

Parts Used:

Linda from Atlanta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

216 of 425 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

one of my burners would only work half the time, and you had to wobble it to make it work

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

Parts Used:

cindy from Sebeka, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

138 of 265 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Burner was getting too hot and you could not regular the tempature

Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one

Parts Used:

Range Infinite Burner Switch - 8 Inch

Dennis from Hagerstown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

76 of 85 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

We needed new drip pans and no one carried the model we needed

we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Parts Used:

sylvia from ventnor city, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

67 of 71 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced drip bowls in stove

Took out the old drip bowls and replaced with new bowls.

Parts Used:

Liza from College Point, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

69 of 132 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rented appartment in which none of the drain pans were the proper size making it very difficult to cook

I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.

Parts Used:

Grace Mary from Canton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

65 of 129 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

installed new switches and elements

just move one wire at a time. Each switch has 5 wires and I am sure mixing them would not be good.

Ordered parts, they shipped same day. Arrived exactly as predicted. Totally non-stress. Can't find a thing to complain about.

Thanks PartSelect

Parts Used:

Range Infinite Burner Switch - 8 Inch

Infinite Switch - 6 Inch

Robert from Santa Fe, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

17 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner was out but the burner coil worked on onother burner

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Parts Used:

Richard from Orange, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

10 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner heat does not turn down

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

Parts Used:

Range Infinite Burner Switch - 8 Inch

Gary from Blanchester, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

9 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner receptacle burned out

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

Parts Used:

Michael from N. Haverhill, NH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner would only cook on high setting or not heat up at all.

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

Parts Used:

Infinite Switch - 6 Inch

Judy from West Salem, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

9 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

electric coils would not stay flat as drip pans were incorrect fit

replaced drip pans with correct type

Parts Used: