A310 - Instructions

first i removed front panel by pulling it from the bottom and then removing the top. then i removed the agitator with a 1/4 nut driver. then i had to open top lid which is hinged and held together by two 1/2 inch bolts. after i opened up the top of the washer i had to remove the white plastic top of the inner tub. in order to remove the inner tub there is a large nut that i had to use a punch and a hammer to break it loose. don't forget this nut is counterclockwise to loosen.hint use a little wd40 due to calcium build up around nut. once the inner tub is removed you should see the rubber bushing. be sure to remove all rust and water calcium build up before installing new bushing. i used a wool pad. put everything back together the way you took it apart and it should fix your leak.

A tension sping on the motor broke, smoking the drive belt.
step1...remove front of the washer to access spring, tip washer back & prop on short 2 x 4 board. 5 minutes
step 2... remove one end of pump belt to get new bely up to drive pulley put on belt using fingers only & replaced the end of the pump belt....2 minutes

step 3...put new spring under motor & hook one end in attaching hole on motor, reach through with pliers to grasp spring to pull end to attach spot on base...1 minute

It took longer to open up the washer front & prop it up that it took to repair it. This is a siper easy repair!

removed then installed new unit by hand. received order the next day-am. delivery time great.

I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.

There is one good description already posted. I would add:1)If the the nut holding the inner tub doesn't loosen easily just split it with a chisel and don't waste time. 2)Don't order extra washers to remount the outer tub, they come with the bearing! 3)While disassembled I ran the spindle on spin to make sure the brake assemlby wasn't the problem. It ran quietly and smoothly. 4)The inner bearing sleeve was stuck on the spindle and didn't want to free up. I used a rotary tool to cut a groove in the old bearing sleeve then chiseled on the groove edge and it split nicely. It was very brittle. The washer seems to work well now. Next time I see a leak I am going to repair it right away!

First I removed the two screws that held the front panel in place. Then I determined that the belt for the pump had fallen off because the drive belt was worn (and inverted) and a piece was hanging off and causing the pump belt to slip off the motor. I replaced the belt for the pump (Temporarily) to allow the tub to drain.

I replaced both belts with new belts and returned the front panel. The process took 15 minutes due to the necessity of explaining the proper use of tools to a neighbor child and allowing him to assist (required for the completion of one of his Cub Scout requirements).

1st We pulled the washing machine from the wall and unplugged it. 2nd We tilted the maching back against the wall so that we could see all the pullies. 3rd. We removed the two screws that afix the front panel on the lower part of the washing machine and removed the panel. 4th We removed both belts and put new belts on. 5th We put all parts back in place and plugged maching back in, slide it back in place. 6th It worked like a charm and I proceeded to wash 3 loads of laundry that evening. The only tool we needed was the phillips head screw drive to take off the front panel. It took us 5 minutes to fix the machine.

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

Well, I figured out a couple of things during this process. #1 The Washer was smoking. It had happened before (a sock got suck between the basket and the tub) so I assumed that happened again. I couldn't see anything in that space this time, so I dissasbemled the washer to see if any clothing was there. Relatively easy once finding the screws to remove the front panel. #2 What I found was a sock in the pump box. I disconnected the hoses and removed it, saw nothing between the basket and tub and ran it to see if problem corrected itself. It still was smoking. That is when I checked the belts, #3 first the pump belt, replaced it, very easy, just pulled the old one off, and wheeled the new one on. It still was smoking, #4 so I replaced the drive belt, very easy and the same as the pump belt. It still was smoking so I lubed the wheels for the belts, and #5 cleaned the residual rubber around the wheel from the old, fried, dry rotted drive belt. No more smoke!!! However #6 remember to leave space between the basket and the top of the tub, as when I put the washer back together the basket didn't spin. I removed the top and ran the spin cycle, it spun fine, reconnected and it didn't spin, the tub top was touching the basket, that's when I relized the top was on too tight. I reattached and left about 1/4 in of space and all is well now.

removed screws on front of washer, removed bolts holding top cover hinged back, nut driver to remove agitator, slipped agitator off, removed tub hoses, did not have special wrench to remove large nut on shaft, used punch and grinder to removed, had new large nut so wasn't concerned about damaging old one, pay attention to thread pattern to know how to turn, if you had special wrench job would be easier, removed spring bolts and took out inside drum and tub. cleaned corrosion and installed new seals, can be hard to slip on new seal, don't use grease, get dishwashing soap to use as lubricant to put on. Put back together and all is good.

Thoroughly cleaned the edges to be sealed with a wire brush and sand paper. shimmed the top piece with 1/4 inch plywood strips. seated the top piece with the seal attached and worked the seal down into place. Positioned the seal clamp, carefully, and tightened the clamp screws. Replacing the seal did the trick, even though the old seal did not look to be in bad shape.

Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

I removed 2 screws holding the front of the cabinet and set the front panel aside. Next I removed the screw securing the relay and water level switch to the front of the cabinet, and removed 4 screws holding the top of the washer to the cabinet. I removed the hose, then removed the 4 screws securing the siphon break to the rear panel and pulled it inside the cabinet. I removed the elbow and gasket, installed the new elbow and gasket, and reassembled all parts previously removed. I reconnected the hose and fastened it to the drain, and I was back in business. It took about 35 minutes.