9825VUV Magic Chef Wall Oven - Instructions

Turn off the breaker. Remove the two screws holding the bake element and disconnect the two wires. Plug the new element in and re install the screws. Trip the breaker back on and test the oven. It works.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

Turned power off by switching off the breaker. Removed both racks from oven. Removed two Phillips head screws at back of oven securing the old heat element. Pulled old heat element forward about four inches exposing the two power wires connected to it. Removed the wires from their connectors. Removed old element. Connected new element to power wires and pushed it back in place. Replaced new Phillips head screws. Replaced racks, and turned power back on. Oven was fixed in less than five minutes. Disposed of old element. Life is good.

Followed provided video

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

Very easy. remove two screwa , pull element forward, unplug.Set new element in place, plug in. push back in. Screw in both screws and your done.

Changed bake element in oven.

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

Upon receiving the replacement part, I noted that the socket was held in place by simple expanding tabs. TURN OFF POWER TO THE OVEN. Using a right angle pick or similar tool, bend the tabs inward on the existing socket and remove. Disconnect the white, black and green wires. Note which tab is the green tab. Attach the wires to the new socket. Push the new socket into place, aligning the key bump on the socket with he slot in the oven wall opening. Install bulb and diffuser.

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

1. Turned off oven electric power at circuit breaker.. 2. Removed 2 screws at coil at back of oven. 3. Pulled coil away from back of oven. 4.Pulled power wire clip up vertically from coil.One clip was too tight to pull up by hand. Used a pair of pliers. 5 Removed coil and put new coil in place with wireclips. and screws provided.