9815XUB Magic Chef Wall Oven - Instructions

turned off power, removed two screws mounting the old element, cut wires, and removed old element, crimped new stake connectors onto existing wiring, attached stake connectors to new element, installed element with two new screws provided, turned power back on.
It would be easier to just slip the two stake connectors off and reinstall on the new element but I elected to install new connectors because the oven was over ten years old and one seemed loose.

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

I removed screws that hold cover and put cover aside. I removed the buttons and removed glass cover. I pulled panel out far enough t get tswitch wires and installed switch. Be very careful not to let wires touch metal.

i needed a rack for my oven i looked everywhere for one that fit could not find one.my oven is not common due to the fact it is for a very small space and only 18 " wide i stumbled on this site by accident and decided to try it out shipping was very fast and people there are very nice any have alot of knoldge about parts it is very well set up to order with just a modle # i have told my whole familey about this site they did a great job and i will be back for more parts.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Clipped the wires back onto new element and used the two stainless screws provided in kit to resecure.

It should be noted that I first called a local Maytag Appliance Co. and inquired about this element. I was told that they would have to order it and it would cost me 68.00 plus tax. I told them I knew what these elements are worth and their price was a gouge. They didn't care. This is a repair that anyone knowing how to work a Phillips screwdriver can perform. Save some money and do-it-yourself.

Thanks Partselect!

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

Fortunately, we had read the instructions on line, because none were included with the part. Still, it was REALLY easy. We unscrewed the two screws, pulled the element away from the back wall and pulled the wires off the contacts at the back. (That was the hardest part, because they were stuck-on well. WD-40 was helpful here.) The one piece of paper that did arrive with the part told us the ground wire was no longer necessary if you use the new screws that came with the part, so we ended up cutting the ground wire off. We then put the other wires back on the new contacts, pushed it back into place, and re-screwed it to the back wall. We have used the oven several times since, and it's all working well.

I removed the two screws holding the element in place and disconnected the two wire terminals.
I then reversed the above steps to insatll the new element. SUPER EASY!!

no instructions on how to replace element. first i removed the 2 screws that held the element to the oven. then i pulled the element out with the wires attached. at first i couldn't tell how the wires were attached - i thought they may have been soldered on. it took awhile for me to figure it out the wires were attached to a part that pulls up off the element part. no solder was needed. after i figured that out, easy to pull the part up off the element part.

The replacement switch was slightly larger than the old one so it would not go through the hole in the front panel so I had to get a reaming tool and enlarge the hole just a little for the switch to go through. It was still an easy repair as I had the proper tool.

We received a used oven for free. It was in like new shape but the handle disappeared during transport and installation.

I drilled two holes on the plate and I did use same original screws.

I just wanted to say once it was installed, It worked great.

Thank you,

Sam

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!