95-1997-00-01 Tappan Refrigerator - Instructions

change the evaporator fan motor kit working perfect

followed the video very esay

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

Watched the video once. Removed four 1/4 inch screws with a nut driver unplugged the unit, took out two screws securing the timer. Replaced did all of this in about 10 minutes. It was "exactly" as the video showed and it's worked perfectly since the replacement of the faulty timer. I saved a $75.00 service call minimum and the part was more than likely cheaper from Part Select than from the repair facility. Although I'm a pretty good handy man, you would not need any experience to make this repair. The instructions are precise and the part fit perfectly.

Simply replaced the defrost timer located inside the frig just behind the temp dial. Very easy job. Removed the 3 screws holding the temp sw and light assembly. Removed the defrost timer w/ 2 screws and put i all back together. 15 mins at most. Suggest you watch the install video for pointers.

tested the thermostat, cleaned the coils, checked seals all clean. defrost timer did not cycle so replaced it but issue not resolved. even though freezer was working while refrigerator was problematic, proceeded to open freezer panel. discovered that fan was not pushing cold air into refrigerator compartment due to ice build up in connecting tubes. cleaned ice and replaced panels to positive result

1. Disconnected electrical. 2. Removed upper console in refrigerator by removing 2 nuts. 3. Disconnected wiring from console. 4. Removed 2 screws from defroster timer part and pulled off from connector. 5. Replaced with new defroster timer and put everything back together. Thank you Steve for the U-Tube step by step video.

It was fairly easy to replace the thermostat. Unplug the refrigerator first. Then remove the refrigertor light bulb and 3 screws on the plastic cover that houses the thermostat and defrost timer. Unplug the thermostat from the wiring on the refrigerator and remove the plastic housing holding the thermostat. Remove two screws holding the thermostat and replace with the new one. Put everything back together in reverse order. Unfortunately, this did not corrrect my problem. The refrigerator is well over 30 years old and I had narrowed down the problem to the thermostat because the old one was hard to turn to adjust. About 10 years ago, I replaced the defrost heater in the rear of the freezer compartment for the same problem, and didn't think that would be the problem this time. Well, as it turned out, I checked the resistance on the defrost heater and it was was bad again. I replaced the heater this week I got from PartSelect, and the refrigerator cycles fine now. Replacing the heater is a little more work that changing the thermostat. You have to remove the freezer compartment fan, fan vent, and back inside wall of the freezer section to expose the coils and the heater element. You just need a socket screw driver. Then you have to reach inside and unplug each end of the heater to check it with your ohm meter. A bad element will show up as an open circuit. Then to replace it, you have to maneuver it around to get if away from the coils and remove a couple of clips. Anyone with some common sense can do it, but it can be a bit challenging.

Unplug the refrigerator. You will ultimately need to remove the back panel of the freezer. But first, you will need to unscrew 2 screws on a small vertical fan vent and unscrew two screws on the fan. Maneuver the fan out of the round hole in the back panel and unplug the 3 prong wire connection. Then remove the fan. Unscrew the 4 remaining visible screwson the back pannel and remove the panel. This will expose the freon coils. On this model, the heater has two connections at the top of the coils. Unplug those wire connections. The heater extends down each side of the coils and along the bottom of the coils. Unhook two aluminum ties that connect the heater element to the coils. These ties stabilize the heater element and also prevents any current from flowing along the element because of the touching of two different metalic parts. Maneuver the heater element out of the coils. To install the new heater, reverse the above process beginning with installing the new heater element. If it hasn't already been done, it is good idea to test the old heater element with an ohm meter to make sure that the element is actually bad. The circuit should be open. This is the second heater element that I had to replace on this refrigerator, and it was actually burned in half both times, so I knew for sure the element was bad. Then test the new element to make sure it is good, and start the installation..

I watched the video online where it described the troubleshooting tips for this type of symptom. So I knew exactly what the problem was which is the defrost timer. After the part came in I just unscrewed (4 screws) the box which houses the thermostat and the defrost timer from top ceiling of the refrigerator section. Then I just unscrewed and unhooked the old defrost timer and replaced it with the new one. After finishing the installation I turned the fridge on. At first nothing happened. So I turned the dial on the defrost timer with a flathead screw until it clicked and the fridge came alive. I waited for an hour or so. The cooling cycle completed and the fridge stopped as expected. When I opened the door I noticed the interior is much colder than before and right after closing the door the fridge hummed back into life again. So I know my fridge is working again. Thanks to PartSelect for providing the right part for my refrigerator. I will definitely buy from them again if anything goes wrong.

I order defrost timer then replaced it but it seemed doesn't work. I order defrost thermostat again then it worked fine until now. Thanks. Part selects.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

removed everything from door, removed screws in gasket around door, laid door face down(insulation side up)applied rtv around edge of gasket and door, waited 10 minutes and started with top screw in middle of top then middle of sides and bottom then installed remaining screws checked levelness of refrigerator, the you are done