9475XVB Magic Chef Wall Oven - Instructions

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought

Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.

After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by removing the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!

My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.

I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

I didn't. Don't know how to get to light bulb to change it for this specific model

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.