9122VUV Magic Chef Wall Oven - Instructions

I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

Watch the video, it's too easy and best of all, the part fixed the oven!

Changed out the thermostat, very easy to do. The instructions were the same as I read on this site on a similar fix. HOWEVER, even after making the thermostat change, the heat did not regulate or adjust. Not sure if part is bad, or something else could be the culprit? but if not thermostat which regulates this, what could it be? I'm very impressed with PartSelect as a company and their website is great, but i'm baffled as to this ongoing problem.

Once I noticed the oven failed to light, I checked the igniter and saw it was glowing. At that point I did some research and found that the igniter could still be bad even though it glowed. This was the most common cause of ovens not lighting. A bad igniter will not glow as bright as a new one. An igniter had to draw a minimum of 2.8 amps in order for the safety valve to open and supply gas to the burner. After checking the safety valve with an ohmmeter, I found it to be good, so I ordered a new igniter. Once I received the new part , it took about 20 minutes to install.

Replaced stripped screws with 632 by 3/8 bolts and nuts. Your video helped with the rest of the installation.

Unplug power cord to oven.Remove lower panel from inside of oven to access flame rail cover.Remove wingnut from cover to access flamerail and igniter.Using phillips head screwdriver,remove 2 screws from lower access plate located at rear of oven to access igniter wiring.Disconnect both wires, then using a nutdriver,unscrew and remove igniter from flamerail.To install, simply reverse instructions.It was extremely simple and fun to do.But most rewarding of all was the sense of accomplishment from doing the repair myself not to mention of course the money i saved not having to call a technician. Thanks guys!

Because of the video provided by Parts Select I felt confident before even starting and that confidence stayed with me to the end..I removed bottom of oven , removed the philips screw in the front end of the burner and removed it.. Losened and removed the igniter replaced it and reassembled..The only caution I can give, if you find the screws holding the ignited on the burner hard to take off, apply a SMALL amount of WD40 to the threads and wait a couple minutes before removing..I was fortunat in the fact that my plug matched the replacement part with no cutting of wires..I normally don't get breaks like that.. Thanks Parts Select.

First turn gas off at pipe. Remove oven door, racks and bottom cover. Go to back of oven and unplug oven igniter. Back in front, unscrew 2 nut screws from igniter. To make things easier I tied a piece of string to the plug of the igniter, once I unscrewed the igniter I pulled it out with the string attached. When replacing I tied the string to the plug of the new igniter and pulled it from the back so the plug was able to come through, plug in the new igniter, screw it in place, replace the racks, covers, door and you're ready to enjoy some baking

Based off the information I found online, I determined we had a bad igniter. 1- disconnect oven from any power sources. If you have a gas model, be sure to valve off gas at this time as well. 2- Remove the racks and bottom pan in the oven. There is 2 push/pull locking mechanisms at the back of the oven that hold the tray in. Once you have this out you should have access to the gas tube and igniter. 3- Using a 5/16 nut driver, remove the 2 bolts on the mounting plate and the igniter should be free at this time. 4- Remove the bottom drawer to the oven. This will give you access to the electrical connections. 5- Remove the 2-3 screws that hold on the access panel toward the back of the unit. 6- Following the wires down, find the plug for the igniter and unplug. After this is done pull the wiring up through the oven and it will be the same to put back together just in reverse order. Relatively simple project that should take anywhere from 10-30 minutes depending on how handy you are. After reinstallation our preheat times went from 45 minutes to 10

Hardest part was disconnecting the gas line and moving the range out of the counter. Removed oven door for easier access to the igniter from the front. And the clean up. Installing the igniter was relatively easy from the rear of the range. I was not able to install the igniter through the front of the range because the wires were not long enough to pull the igniter forward through the front so it was necessary to pull the range out from the counter and install it from the rear. Then it was just a matter of removing a small dust cover at the rear by removing one screw. Then removing old insulation and disconnecting wires. Remove 2 mounting screws that held the igniter in place. These screws had to be removed from the front. Pushed the old igniter out through the rear of the range. Connected the new igniter wires. Pushed the new igniter through the rear of range and replace the new insulation. Mounted the new igniter with 2 screws. Reassembled everything and it worked ok.

removed cover over burner section ,removed power to burner section ,removed burner assembly, replaced ignitor assembly, wire in to control circuit ,replace burner section in oven,turnon power chech operation ,replace cover.

Removed door, took off old igniter. Had to redo plug , simple, because kit had wires to splice to make it work. Whole job was 30 min. Recomend to anyone. Saved $75 on a service call. Bill

removed inside trays and grill inside large oven door on front to get to ignitor,removed ignitor with 1/4 drive socket,followed the wires off the ignitor thru the hole in back of oven and disconnected the connector,put on in reverse order.To simple to even write about,anyone can look at it and tell what needs to be done

Remove old igniter ,,again had to remove rear panel of unit to get to connecter..reverse procedure to install igniter. Video very helpful.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.