91195191990 Kenmore Range - Instructions

Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, turn on for a few minutes to make sure it works. Piece of cake.

First I searched this site and read about the repairs - which made me feel like my husband could do it with ease. Then he removed two screws inside the oven, removed the broken element (didn't know it was broken til removed) and replaced the new one - just like that! The real key was being able to read how it was for other people who had already done it. That's the only reason I'm submitting my storey. Thanks

I turned off the power to the oven at the breaker. Then I removed the two screws from the old element, pulled the old element out about 3 inches and disconnected the wires from the element and installed the new one.

Removed 2 screws that hold element and pulled old element out about 2 inches to disconnect the wires from the old element. Connected the new element and remounted to rear oven wall. Very simple and saved a visit from the appliance repairman.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
the repeated the process to complete the installation.
Relly easy.

TURNED OFF CIRCUIT BREAKER. Removed nut, washer and screw, pulled out electric burner about three inches, disconnected electric terminals and removed damaged element. Inserted new element into oven, connected electric terminals, pushed electric prongs back in, screwed element to back wall of oven....DONE Easy as 123

Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!

1st I opened the oven door and removed the 2 screws that hold the outside and inside of the door together. With the door separated I removed the 2 screws that hold the end caps in place, then removed the old end caps. I put the new end caps on the oven door handle, aligned the holes for the end cap screws and reinstalled the screws,then reinstalled the oven door screws,closed the oven door and started cooking.

Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak

First I removed the door by lifting it off the hinge assemblies.

Then I removed the drawer to access the spring.

Removed the spring, noting which attachment hole was used.

Removed the hinge assembly with a Phillips screwdriver.

Replacef the unit.

Repeated for the other hinge assembly.

Note: it took longer to find the correct parts in the parts diagrams than it did to replace them.

Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding

FIRST TURN OFF THE CIRCUIT BREAKERS THAT POWER THE COOKTOP!! Remove the cooktop from the counter by removing the screws from the mounting straps under the counter. Then remove the screws that hold the glass cooktop to the frame and lift off the glass top. Next lift up the bad element and unplug one wire from the bad element and plug it into the new element. Make sure to put it on the exact same terminal of the new element. Do this for all the wires. Remove the two mounting tabs from the old element and put them on the new element. Turn on circuit breakers and your done.

After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.

Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so long as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.

Pull oven door open about a couple of inches. Grab the door by the sides and pull up to remove from the hinges. Set it aside. Remove the storage drawer under the oven. This gives you access to the tension spring attached to the hinge. Detach it by hand. Using a phillips head, unscrew and remove the damaged hinge. Replace the new hinge. Reattach the spring. Replace the storage drawer. Replace the oven door. Done.