Models > 9119344190 > Instructions

9119344190 Kenmore Range - Instructions

All Instructions for the 9119344190
286 - 300 of 335
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The element was too long. Had to bend the connection progs upward to get them to fit.
Took the back off the oven to get to the connection wires better. Took chanel locks and bent the ends of the element upward to clear the back oven guard
Parts Used:
Bake Element
  • gary from floyd, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
element had burned out
Undid bolts removed old element and then installed new one .
Parts Used:
Bake Element
  • Joy from North Attleboro, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Range door was hard to open and would not close completely
I watched the video in the website and in less then 5 minutes replaced the broken hinge with the new one and the door works perfect.
Parts Used:
Hinge with Roller - Left Side
  • Roger from Sandy Hook, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burned out Heating coil
I pulled the circuit breaker then took the racks out took the nut driver and turned out the two medal screws then pulled out the coil very carefuly then i unhooked the wires bbeig careful not lose them i bent them and proceded to hook up the coil with no problem works fine bdwargo@ptd.net
Parts Used:
Bake Element
  • Bernard from Summit Hill, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The Broiler coil burnt out,
pulled out the old one and just put the new one in after shutting down the electric 2 screws is all it was very easy.
Parts Used:
Broil Element - 240V Single Heating Element Support Clip
  • Carol from East Falmouth, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Right Front [surface burner terminal block kit]
We did the repair by following the inclosed instructions. we are elderly retired average ages 82. This was our first repair and it went very well. We are so pleased to have saved over $80.00 compared with hired labor 3 yre. ago for the same part. Thanks so much for your good service.
Parts Used:
Surface Burner Terminal Block Kit
  • Wayne from Montoursville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
large burner would not reduce heat when turned down
unplug stove, unscrew two screws on front of rangetop holding element controlls pry off controll handle and unscrew element controll, swing top up and off hinge.one at a time with needle nose plyers pull off wires and connect on new element controll.
Parts Used:
Large Surface Burner Switch - 2350W 240V
  • carl from orange, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bottom heating element in electric stove was broken
1.)Turned off stove breaker in electric panel 2.)Moved stove and unplugged it 3.)At the back of the stove removed the clips from the bottom heating element 4.)Removed the stove door by opening it half way and pulling up, this makes it easier to reach inside 5.)Removed the heating element bolts 6.) go in reverse order to reassemble. Note: Took the time to give the stove a good cleaning.
Parts Used:
Bake Element
  • Paul D. from Walker, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Baking element burned into.
Removed two screws holding the element in place. Carefully pulled the element from stove, as not to pull wires off element. Removed wires and installed new element.
Parts Used:
Bake Element
  • Robert from Flowood, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Oven element burn in three pieces
It was not a repair, just a replacement of the element. Very easy and no challenges at all.
Parts Used:
Bake Element
  • Willard from St. Helens, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Oven not heating although the broiler did heat.
Turn off range circuit breaker; remove and save nuts holding old element; disconnect old element from wires; connect new element to wires; tighten new element in using the nuts you have kept. Turn on the breaker, turn on your oven. WARNING: INSULATION SHOULD BE KEPT AWAY FROM CONNECTED WIRES, OTHERWISE IT BURNS WHEN OVEN IS TURNED ON AND YOU WILL HAVE TO UNDO THE NEW ELEMENT AND PUSH THE INSULATION OUT OF THE WAY AND THEN REDO THE NEW ELEMENT.
Parts Used:
Bake Element
  • Bobbie from University Place, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
element broke in 2 pieces
removed broken element and installed new element when received from UPS -very simple -
Parts Used:
Bake Element
  • Nancy from Louisa, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Plastic Roller on hinge broke in half
Following the repair video made the job very easy and quick, about a 5 minute repair. Wife says oven door never worked better. Thanks a lot for all your help.
Parts Used:
Hinge with Roller - Right Side
  • Dan from Granville, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
one oven hinge broken
It took longer to watch the video on how to replace the hinges than it did to replace them. Simple and easy. Video knocked it out of the park for ease. And now the oven door works great! thanks!!!! Video suggested if you're replacing one side do both, couldn't agree more.
Parts Used:
Hinge with Roller - Right Side Hinge with Roller - Left Side
  • Bonnie from Tucson, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken roller on hinge
I unscrewed the broken hinge, removed the tension spring and replaced the old hinge with the new one. total time 5 mins works great.
Parts Used:
Hinge with Roller - Right Side
  • Frank from East Moriches, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 9119344190
286 - 300 of 335
Back to Top