Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 91193402992 > Instructions

91193402992 Kenmore Range - Instructions

All installation instructions for 91193402992 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 91193402992
76-90 of 334
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Needed New Burner Bowls

  • Customer: Carolyn from Garden City, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Removed the old burner bowls, replacing them with the new ones.

One of the two wires slipped back into the void space.

  • Customer: Alvin from Pensacola, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
I ended up having to re-move the back panel on the stove to access one of the wires, so that I could pull the hot wire back through the inside of the oven. The connection to the bake element was then made simple and easy. My time lost was removing the back panel and re-installation. I can not complain about the repair problem. I saved at least a couple hundred bucks. So that's my story. Thanks for the response in expediting my order of the exact bake element.

Bake Element cracked

  • Customer: Kevin from Grovetown, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
Pulled the range out from wall (which took most on the repair time to do), removed back cover, pulled of terminals, went inside oven a remove the two screws holding Bake element. Inserted new element, tighten down screws, etc.............

bake element fried and broke in 3 pieces

  • Customer: Surya from kingston, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
I removed the two screws that hold the element, then I took the back cover of the range to have access to the wires, after that, I took the old one out, placed the new one and finally hooked the wires and placed the two screws right back. Very easy. I thought about bringing someone to do the job, and after I was done, I couldn't believe how easy it was.

Broiler coil burnt out

  • Customer: Howard from LEXINGTON, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.

The previous element decided it was really an arc welder

  • Customer: Robert from Clermont, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
First cut the power at the breaker and then removed the rear panel of the range. Then removed the two retaninig screws in the oven and then unplugged the old element in the back. Cleaned out the molten metal and remains of dinner and installed new element same way the old one came out and voila, oven is back in operation.

Replaced the outlet the one of the top burners on top of my stove, it went very well.

  • Customer: Charles from MECHANIC FLS, ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.

Bake element in the stove went out

  • Customer: Richard from HERMITAGE, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Unplugged the stove from wall, pulled out oven racks. Unscrewed 2 screws that attached the burner to the oven. Pulled the two wires off, be careful not to let them go back into or behind the oven wall, then you would need to take the back center panel off and push them back through. But I bent the wire enough when taking them off to make sure they rested on the inside of the oven wall, got the new burner attached it to the two wires, screwed it back in the oven wall and I was done. Plugged it back in and works beautifully. Whole thing took maybe 15 minutes 30 minutes tops.

Old drip bowls were badly tarnished . . . shine could not be restored.

  • Customer: Paul from PROVO, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.

burner terminal block was worn out

  • Customer: Mario from RENO, NV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you

Previous owner left racks in during self clean

  • Customer: SHARON from EDMOND, OK
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Took the old racks out andcslipped the new ones in

Broken bake element

  • Customer: Scott from ROCHESTER, NH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Remove screws on bake element and on back cover to wires (unplug unit first) remove terminal ends , replace element put cover back on and screw in element hold down screws.

bake element burned out

  • Customer: Gary L from DEER PARK, WA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Had to move the range out of its little cubby hole in the kitchen so that I could have access to the back of the range. This process probably took the longest. After that it was a piece of cake. Took about 15 minutes to complete the job. So easy, eve a caveman could do it.

unit burned out

  • Customer: Robert from KALISPELL, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
To 80 year old (young) brothers worked together. One hooked the wires the other one plug it in. Very simple install.. Neither one knows anything about electricity. Thank you for your service.

element burned out

  • Customer: raleigh from gresham, OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.
All Instructions for the 91193402992
76-90 of 334