Models > 9119328111 > Instructions

9119328111 Kenmore Range - Instructions

All Instructions for the 9119328111
1 - 15 of 26
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Parts Used:
Surface Burner Terminal Block Kit
  • Shaohui from East Lansing, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
48 of 52 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Parts Used:
Surface Burner Terminal Block Kit
  • Gregory from Mont Belvieu, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
23 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could not find the correct replacements (burners & drip pans)
After months of buying the wrong parts & cost I discovered this site So easy to order & quick delivery, plus very easy installation. Thank you. I also wanted to add that the reps (Tanisha & Matthew) were extremely helpful & informative. I can only hope all the reps equal their performance. I will definitely be using this site, before any other source. Knowledge & cost is also important to me & that need was met. Good job!
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Barbara from JEFFERSON, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
13 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element dangling
Snapped in the clip
Parts Used:
Single Heating Element Support Clip
  • Victor from Miami Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Single Heating Element Support Clip was needed to hold up the heating element in the oven. Old single heating element support clip broke and came out of the hole.
Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D
Parts Used:
Single Heating Element Support Clip
  • Marion from METHUEN, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old single heating element support clips came loose over time.
I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.
Parts Used:
Single Heating Element Support Clip
  • David from SALISBURY, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
heating element clap broke off
All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.
Parts Used:
Single Heating Element Support Clip
  • James from Hedgesville, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Have tried 3 different store-bought drip pan sets over the past year. None of them laid flat.
Simple installation of new pans and all are level! Thank heaven! Thank you, PartSelect!
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Jennifer from Saginaw, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
10 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
A tenant left the Drip Bowls in an uncleanable state. I could not find a suitable replacement..
Most trainable people can pull out the heating elements and replace the Drip Bowls. The great thing about the ordered drip bowls was that they FIT! Most drip bowls sold as easy replacements for GE or Hotpoint appliances do not fit and wobble the heating element or drip bowls. If not fitting correctly, the tenant usually destroys the heating element and the drip bowl.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Larry from SACRAMENTO, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hanging broiler
Quick and easy, thanks!
Parts Used:
Single Heating Element Support Clip
  • Doris from Aberdeen, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
support clips fell out
Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.
Parts Used:
Single Heating Element Support Clip
  • tomi from dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the drip bowls were worn out
simply replaced them.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • linda from STANTON, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowl from a big box store was too big even though both say 8”.
Ordered the part and set it in.
Parts Used:
Drip Bowl - 8 Inch
  • Kathleen from INCLINE VLG, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pan was ruined by renter
I ordered a new drip pan. Piece of cake. Stove looks new again.
Parts Used:
Drip Bowl - 8 Inch
  • Karilyn from KEWADIN, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowl, was very hard to find one that fit my stove
Installed easily, was most impressed with the speed of delivery and it was the perfect size!!
Parts Used:
Drip Bowl - 8 Inch
  • Rosemary from BROOKFIELD, CT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 9119328111
1 - 15 of 26
Back to Top