Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 7MMPM0060VM0 > Instructions

7MMPM0060VM0 Maytag Washer - Instructions

All installation instructions for 7MMPM0060VM0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMPM0060VM0
511-525 of 709
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Old seal split

  • Customer: Gary from DuBois, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Seal on the lid split. New seal easily replaced. It just snapped into place.

Would not spin during spin cycle.

  • Customer: James G from Crossville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.

Motor Coupling failed after 20 years!

  • Customer: Brian from Spring Hill, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Determined based on some Internet searches that the part that we needed was the motor coupling; washer would not spin or agitate. Once I figured out how to removed the cover (by the way, one of the guys at an appliance store told me how to do it), and reviewing the video on your website, I removed the two screws and four clips, dropped the motor, inserted the parts and put it back together - all in about 15 or 20 minutes. It was easy and clean and the washer worked again. Hopefully go for another 5-10 years. Thanks.

The washer wouldn't spin out

  • Customer: Karla Ann from Neenah, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
went to you tube and watched a video on how to take it apart and replace the clutch assembly.

Bad Motor Coupler

  • Customer: Hilary from Gainesville, FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
So, the instructional video was great but be warned that you REALLY need to hammer the part into place. Basically hammer it into place so that the end of the shaft that it goes on is flush with the plastic piece of the coupler on both ends. Otherwise, you'll put the washer together and run a load and it'll squeal and smell like burning rubber. We had to take it apart like 3 times before we got it on there securely enough. We would then run an empty load and it would be fine but as soon as we would add clothes the squealing and burning would ensure. So, my advice is to hammer it in well and save yourself the time and struggle!

The washer would turn 45° by finish spin

  • Customer: Fred from Hico, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
With no broke springs I thought that they might be weak so I ordered them but didn't install them as I found that the basket had a drag at one point of turning it, so I took it down to the clutch and found the nylon arm that released the brake had the small pins broken off. This would cause the brake to not release full enough that the eccentricity in it had a drag spot during the spin causing tremendous vibration. To disassemble I took the transmission off and the basket off and install new clutch assembly with the basket laying horizontal on a table. I did notice that the new clutch only had three pads on the band and the old one had six. I called you back with no satisfaction, but was given the phone # of the manufacturer and they confirmed that theirs had six pads but the part # checked out so I installed it. It now sits basically still during a cycle. I made and supervised the making of parts in a machine shop all my working carrier and I don't understand the weak link of the nylon pins milled / molded on a part that takes a lick from the actuator every cycle. It appears to me it was made to break, but it is about 20 years old. Thanks for your video help on the tube. Fred

Washer woulp not spin, brake cam driver not like video

  • Customer: Jody from Elk Creek, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
changed parts easily, following the video. Problem was the BRAKE CAM DRIVER, the plastic piece that fits around the shaft near the drum. The old one was visibly torn up, the pegs worn off, the whole thing worn down. The problem with the repair was the video showed an "E ring" holding it on and my washer had no E ring, had nothing hold it. It just sat there. Installed it anyway, although I was worried it was too loose. Sure enough there was a problem. it spun initially then started that ugly clicking noise. turned off washer immediately, disassembled again, and prayed. I found a large flat washer to take up the slack between the clutch and the plastic brake cam driver, reassembled, tightening the nuts a fair bit tighter than before. both the nuts on the transmission and the nut on top the agitator. works perfect!

direct drive motor coupling

  • Customer: Eugene from Chiefland, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

would not spin

  • Customer: Richard from Somerset, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the the drain hose from the pump. Removed nut from the agitator. Then laid the washer on its back after removing the inlet hoses. took out the pump, remove wire harness from motor then removed the motor. removed the three bolts holding in the the transmission. The one mistake I made was that I removed the springs for the brake shoes and this cause me to have a lot of trouble trying to put them back on. Once the clutch arrived, I removed the old clutch from the transmission shaft, and installed the new clutch using all the parts that came with it. Then put everything together in the reverse order that they were removed in.

no spin dry

  • Customer: Walter from West Palm Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
... exactly as shown in the video in addition to shutting water, removing hot & cold lines & waste tube. I was amazed at how fast the parts were delivered in two days regular shipping. Machine now purring a wifey happy once again! Thanks for the great service & video! I recommend PartSelect highly! WSD

Extremely wild rocking in spin cycle

  • Customer: Bryan from Midland, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

Tub was spinning only part time. Had to have help getting started

  • Customer: Kingsley from Ewing, IL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

There was a hole in the outer tub

  • Customer: Kevin from Boise, ID
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to you tube and watched a video on how to take my machine apart.Everthing went great.I did need to buy a spanner for $23.00 @ an appliance store.

Tub will not spin

  • Customer: Rick from Terre Haute, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Washer would stop during any cycle until lid is opened and closed.

  • Customer: Edward from Denver, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the washer. Removed the 2 screws on back of control panel. Pulled the control panel forward. Flipped the control panel back. Disconnected the cable from the lid switch. Removed the ground screw with a nut driver. Opened the washer lid. Removed the lid switch. Snapped the new lid switch into place. Closed the lid. Installed the ground screw. Installed the lid switch cable. Put the control panel back in place and pushed back. Installed the 2 rear screws into the control panel. Plugged the washer in.
All Instructions for the 7MMPM0060VM0
511-525 of 709