7MMMS0100VW0 Maytag Washer - Instructions

Based on all the other info here, I thought "ah-ha! I need to replace the clutch assembly". So I ordered the part, it came the next day (to Vermont, even!) and started to disassemble the agitator, motor, etc. just as shown in the video. I don't think I would have attempted it if it had not been for the video. It made the process seem very straightforward and easy, as long as you are comfortable using a socket set.

That said, there were some fairly minor differences between my machine and the one in the video, so your repair might differ a little. First of all, I did not need one of those spanners / tub wrenches (whatever they called it in the video-- the thing he hit with the sledge hammer) to take off that nut under the agitator. I didn't need to remove it, and the drive axle just pulled right out. Second, you really don't need to remove the motor mount. Just take the motor off, and then go right to removing the three bolts on the transmission.

Actually, my problem turned out to be NOT the clutch assembly, but the little plastic gear things that go between the motor and the transmission, fitting into that rubber ring thing. I lifted the motor off and one of them was sitting there in pieces! You can easily order this part, and it's even easier to install than the clutch assembly. The plastic pieces are reinforced with metal now, which seems like a good idea.

All in all, this was a fun little project, and now I am under the (probably false) impression that I can repair any problem with washing machines!

The video was well made and made repair easy. I like the fact the video also showed how everything went back. The most difficult part and most time consuming for me was putting the washer cabinet or housing back on. I had a hard time lining the sides onto the slot to lock in place....the minor cut on finger sustained during the process was worth it. It saved me from buying a new washer and the whole family are happy that they don't have to wring out the clothes before putting it the dryer. Thank you!

removed the top cover (with all the knobs on it) by releasing the holds in the back
removed the screw holding the lid in place
pinched the snap and removed the part

pinched the snap on the new one and seated in in the hole
screwed in the screw (lol)
turned on the washer

I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

Followed the instructional film that was included on website.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Pull the washer out away from the wall and tip back.
I used a small metal ammo box to hold up the washer.
The bottom pump retainer is easy reach and remove with a flat screwdriver. I was able to pry off with my hand.
Replace retainer insert into slots on drive motor and twist.
I used a pair of Channellock pliers to lift retainer while pressing along the
side till it snaped into place.
Remove the support box and put washer back.
Then tip washer forward to reset self-leveling mechanism.

My factory drain hose had a hole in it, that I replaced with a hose from Lowe's. This was my first time doing this, took some time and difficult. I found out after replacing it, that it was not the right fit, as the drum would bounce around during every wash. After 3 months, due to the bouncing of the drum, that house had a hole and needed to be replaced. I chose parts select, and although the specs of the hose listed it as shorter in length than the one I bought from Lowe's, it fit perfectly and fixed my lose drum. I had watched the video on parts select numerous times (swapping out hose) so this was done in less than 10 minutes. I have become a pro at this and it is all thanks to parts select. Thank You!

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.

Order new hose from Part select. It arrived a couple of days later. I took the old hose off with a pair of pliers, put the new one on ran it thru the hole in the back of the machine and I was done. Total of maybe 20 minutes.

Replace front legs. Very easy fix.

First time .Replace the clutch .miss placed one of the retainer clip .found it after the replacement came .It was in the fold at the base of the machine.

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.