Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 7MMMS0100VW0 > Instructions

7MMMS0100VW0 Maytag Washer - Instructions

All installation instructions for 7MMMS0100VW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMMS0100VW0
181-195 of 283
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer was vibrating badlyt

  • Customer: Michael from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

washer wouldnt spin

  • Customer: miguel from el paso, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I was in need of a second washer to wash heavily soiled clothes my daughter in law younger sister was throwing one away so I asked what was wrong with it and was told it wouldn't spin so I thought it would be an easy fix I brought the washer home did a quick check and with the internet guide I was able to determine the problem I ordered the part and thank god once the part arrived I was able to do the repair within minutes now I have a second washer to due heavily soiled clothes and no more trips to the laundry mat thanks a million to your step by step guide couldn't have done it with out you

would not run after filling with water.

  • Customer: Nels from South Haven, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
lid switch was intermittant for awhile befor finnaly quiting..Unplugged machine from elec. then removed four screws on back of instrument/dial panel...lifted the panel and located switch on left side...unplugged switch and removed screw from ground wire..removed switch...ckd part # and ordered part....part arrived on 2nd day after ordering...installed new switch...plugged switch back in..connected ground wire....replaced panel installed four screws... plug machine into receptical and ran a cycle to test. everything working fine.. I tested continuity of the old switch ..it was fine the problem was with the plastic spring that holds the switch in the slot...and allowed it to move thus not allowing the contacts to close. ground wire screw and two of the other screws required a nut driver..the other two crews required a phillips head screwdriver...10-15 min to remove switch and order...less than 10 min to replace switch and put the panel back on. location of my washer allowed me to work on it without moving it...if it is backed up to a wall..it will have to be moved enough to reach the screws on the back.

washer filled with water but would not wash, spin or drain

  • Customer: Charles from Waxahachie, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Used part PS886960. Simple process to replace - removed the two screws and flipped the part that houses the controls/electrical over. The switch was easily accessable. When changing out the switch the wire inside the old connector had previously gotten hot and bonded inside the plastic. Had to use a pair of pliers to separate. Then there was part of the copper piece still stuck in the connector. Used a drill to remove the bonded piece and jammed the two fittings together. Washer is repaired and working fine. Should have taken about 10 minutes to change the switch but required about 30 total.

washer wouldn't start

  • Customer: David from Seminole, OK
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Parts Select is outstanding..They diagnosed the problem quickly..The part was sent within 2 days and we were washing laundry the 3rd afternoon...THANKS!!!!!!

Clutch went out

  • Customer: David from Colorado Springs, CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Just watched the video provided by parts select and then went to work. Excellent video. If I had been better mechanically inclined it would have been much faster. Thank You Parts Select! Also fast shipping.

The spin cycle got weaker and weaker and it couldn't spin the wash.

  • Customer: Mark from Middleboro, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched a vidio on YouTube and figured the problem.then I tryed to find the clutch local but no luck! So I yahooed it and found this web sight,I ordered the the part and it came in a few days.The part showed up on a Friday and I put it in the next morning.I watched the link your parts sight refered me to and was very good ! I got all the tools together and started the project,it wasn't the exact same unit but it showed you enough to figure it out.I ran the vidio as I did the project and it went smoothly.I am very happy with the parts, the web sight and the lincks it shared with me . I booked marked the sight for future reference and have already shrared it with someone who has the same problem. thank you for all the help!

The agitator had stopped working

  • Customer: Jack from Matthews, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
We got the parts, watched your video a couple of times and then began the repair. It went well with one exception. None of my socket extensions were long enough to work well. The required length might be added to the video and the printed installation instructions. Also it would have nice to have been able to order a small tube of the recommended lubricant. Overall I was very pleased. Jack

Washer wouldn't cycle

  • Customer: Steven from El Paso, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This is a relatively easy repair. The difficult part is removing the housing that holds the timer and other knobs. However, once I realized how it comes apart, it is very easy. I removed more of the housing than I needed to in order to get to the timer. You DO NOT need to remove the plastic side panels on the housing faceplate. Once the timer is exposed, one screw and the knob holds it in place. It is very easy to remove and there was an small instruction label advising how to remove the knob. Without that, I would probably have broken the knob trying to pull it off. Once everything was removed, installing the new timer was very easy. Putting everything back that I had taken off was straight forward and would have been even easier had I not taken more things apart than I needed to. I watched a video on the Whirlpool parts site that showed how simple this is to accomplish, unfortunately, I watched it after I had already started the repair job. I would definitely recommend doing this yourself. It saved me a ton of money I'm sure.

Would not spin during spin cycle.

  • Customer: James G from Crossville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.

The washer wouldn't spin out

  • Customer: Karla Ann from Neenah, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
went to you tube and watched a video on how to take it apart and replace the clutch assembly.

The washer would turn 45° by finish spin

  • Customer: Fred from Hico, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
With no broke springs I thought that they might be weak so I ordered them but didn't install them as I found that the basket had a drag at one point of turning it, so I took it down to the clutch and found the nylon arm that released the brake had the small pins broken off. This would cause the brake to not release full enough that the eccentricity in it had a drag spot during the spin causing tremendous vibration. To disassemble I took the transmission off and the basket off and install new clutch assembly with the basket laying horizontal on a table. I did notice that the new clutch only had three pads on the band and the old one had six. I called you back with no satisfaction, but was given the phone # of the manufacturer and they confirmed that theirs had six pads but the part # checked out so I installed it. It now sits basically still during a cycle. I made and supervised the making of parts in a machine shop all my working carrier and I don't understand the weak link of the nylon pins milled / molded on a part that takes a lick from the actuator every cycle. It appears to me it was made to break, but it is about 20 years old. Thanks for your video help on the tube. Fred

would not spin

  • Customer: Richard from Somerset, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the the drain hose from the pump. Removed nut from the agitator. Then laid the washer on its back after removing the inlet hoses. took out the pump, remove wire harness from motor then removed the motor. removed the three bolts holding in the the transmission. The one mistake I made was that I removed the springs for the brake shoes and this cause me to have a lot of trouble trying to put them back on. Once the clutch arrived, I removed the old clutch from the transmission shaft, and installed the new clutch using all the parts that came with it. Then put everything together in the reverse order that they were removed in.

Extremely wild rocking in spin cycle

  • Customer: Bryan from Midland, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

There was a hole in the outer tub

  • Customer: Kevin from Boise, ID
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to you tube and watched a video on how to take my machine apart.Everthing went great.I did need to buy a spanner for $23.00 @ an appliance store.
All Instructions for the 7MMMS0100VW0
181-195 of 283