7MMGL6741TW1 Maytag Dryer - Instructions

I watched the video and did exactly what I was shown. Piece of cake. Thanks!

I am still waiting for my husband to install the push to start switch I ordered. Very happy with the fast service I received from PartSelect but I can't say the same for my husband. So far, it has been a week since the part arrived and it is still sitting on top of the dryer. Any suggestions would be helpful! :)

I removed the top of the dryer and removed the faulty switch form it's mating connector. The simply removed two Phillips Head round headed screws with a screw driver and replaced the part all within 15 minutes. However, I also heard that it wasn't drying properly so after making sure my dryer vent was free of any lint build up, I removed the back of the dryer. Once removed, I completely cleand any dust from inside the dryer, then checked all of the visable wire connections and then went to PartSelect's fantastic web-site. Her they catagorize the top 7 reasons that could cause the problem (in my case) not drying and thenproceed to give you an idea of the most likely cause by publishing the failure rat in per centage values in decending order, they also provide schematics and the on top of all of that...they provide mini-videos not only showing you wher the parts are located but the step by step instructions on how to remove them and replace them. After all of this, I took my ohm meter and actually removed all of the 7 parts suggested, cleaned them up, ran a continuity check on each part and found them all in working order. Replaced the parts and checked the heat and it was back to normal!! There must have be a lose connection causing the problem. But, I can guarantee that the next time I have an appliance problem...I'll again be calling on PartSelect.com. They are awesom and they will be highly recommended to anyone I know that is experiencing problems. I have not ever seen a web-site that was so complete in excellent service. And there prices and shipping time speaks for itself. They are great!!

Watched that igniter glowed for usual 15 seconds. Gas did not flow so tested solenoids for ohm resistance across leads. One was bad, less than 1350 oms (as I recall). Ordered the M series coil (solenoid) kit at Part Select, arrived the next day. Replaced them in 5 minutes. Took about 15 minutes to vacuum lint + dust out base of dryer area. 5 more min to put front of dryer 4 screws in and mount dryer door!

The repair on replacing the clothes dryer belt went great. Not only did Part Select send me the correct belt at a great price .. the helpful hints that other people gave was most helpful. The only glitch was when I was pushing the tensioner wheel to get the belt around the pulley it slipped and the spring came off. The instructions/tip of taking the drum out and how to replace it came in handy when I had to get the spring back into place. The belt finally went on but there was a slight twist in it by the tensioner wheel. Again the tip I got with my e-mail helped as I manually turned the drum and was able to right the belt. Kudos to the tips I received and the confidence I could do the job myself!!!!

Unscrewed bolts off back (2). Took dryer vent out unscrewed the bolts (2) pushed top back and lifted up. Open door unscrewed the bolts (2) to the safety switch pulled the connection (wires) apart and replaced with new safety switch.

push in on clips on front top at seams apx 2-3 inches from both sides. lift lid lean it back. remove door switch. remove front panel. remove old belt. replace with new belt lifting drum slightly to get around drum rib side down. reach in and push tensioner down to the left place belt around pully and over tensioner relase gently put all item back together.

1)Pulled electrical connectors off each of two gas valve coils. 2)Removed two Phillips screws and removed coil retainer bracket. 3)Lifted off two old coils and replaced with two new coils. 4)Replaced coil retainer bracket and plugged back connector on each coil; total coil replacement time is less than two minutes. 5)Confirmed gas valve opens and gas ignites every time over a two day test period. 6)Re-installed door. Wife Happy. We spent under $20 for 'M' series new style coil kit; and the $7 shipping got it here in two days. What a deal! Terry Rahmer 8.24.2012

the repair was an easy fix, I removed the two screws from the brackets holding the coils, disconnect and removed them installed the new coils connected plugs turned on dryer and I got heat not bad at all thank you for the help

After researching the problem, I thought the solution would be to replace the two terminal coil valve, but wasn't 100% sure it wasn't the 3 terminal coil, so I bought both. the dryer is 13 years old so I thought it deserved new coils. My husband was away for the week and I had about 10 loads of laundry to do. I dreaded the thought of going to the laundromat, so I went ahead and ordered the parts, thinking I would call a handyman to install them once they arrived. However, I found a Youtube video showing exactly what I had to do and thought it looked easy enough. I unplugged the machine, removed the front hatch and the 2 small screws holding the coils in place. I unplugged the old coils, used a vacuum to remove the dust in the area and installed the new coils. I popped them back into place, screwed them in, replaced the hatch, plugged the machine in, and VOILA!!!! A dryer that heats!!!!

Watched Youtube video first then followed directions included with belt. Very simple and easy to follow.

I watched a youtube video about how to replace a dryer belt. I did what it said.

Followed the On Line Repair on my Lap Top. Very Easy !

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

Thanks to your video my husband felt very confident and the belt was installed with no problems.