7DU920PWKQ0 Whirlpool Dishwasher - Instructions

Broken latch on dishwasher prevented operation
Door Latch Bolt PS11741367 replacement instruction.

There are no instructions known to mankind on this part, however I did manage said replacement through determination and beer. First I looked it up on the internet. All kind of results, except for the model I was working on. Called, very nice woman directed me to yet another YouTube presentation for another model. As this was no help, I chose to not call her back. Not her fault.
So, I did what every instruction for the other models called for, disconnect the power. Seemed like a good idea if everyone suggested it. After that, remove the inner door by removing the screws. At this point I would like to mention that I also ordered and paid for what I thought would be a set of inner door screws to replace the old and weathered ones. However, they sent me one screw.
Who in their right mind would pay $5.10 for ONE SCREW? Well, your looking right at him. I felt like I sold the family cow for a magic bean, but that’s another story.
So, without instructions, I compared the part I ordered with the one installed in the door. It matched up in many ways, with exception for the fact I would not budge from it’s position, wiggle yes, remove no. I stared at it for 10 minutes with no further progress. Something has to give. I decided to remove the cover of the electronics with the hopes and optimism of a child. It also did not want to be removed. Back to YouTube and the computer. Nothing. I stared at it for another 10 minutes. Drank a beer, and started to “horse” it off, somehow it became ajar, and was finally removed. Upon examination of the old door latch bolt, I noticed that it was attached to the electronic mass by 4 wires. I used my phone camera to record which went where with false hopes that the repair was in reach. It was either me or the dishwasher. At this point, good money was on the dishwasher.
After recording and removal of said wires, I took the entire door latch and whatever the other piece was, to a table for further study, and another beer. After said study and beer, I remembered looking at other parts, one came to mind, a small teflon rod. As I look upon the part I knew about, I noticed it was adhering to the alien part with wires by 2 small teflon rods. I found a small nail, and pushed them out of the part, and they final separated. I replaced the old part with the new one and then reversed all steps and procedures, attached wires, reattached electronic cover, screwed down the inner door, shut main door, and started a dish cycle. Works perfectly. You may ask about the expensive screw. I took it to a local jeweler, who found nothing remarkable about it. As there must be SOMETHING about it that makes it valuable, so I had it mounted and framed in a nice display case for friends and family to treasure for years to come. A real conversation piece, and one more thing to dust.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

I disasembled the inner door and replaced the door switches with new ones.

I removed inner face of door, cut wires leading to door switches, and then installed the new door switches and wire harness.

My wife noted wood floor bucking up around dishwasher - pulled dishwasher out from counter, tipped it on it's side, looked underneath, & noted slight corrosion on top of motor -

Took motor/pump assembly completely off of dishwasher (comes out from the bottom) by flipping four little plastic cams on motor to the side & then took pump apart (starting at top & working down) till I got to the impeller/motor shaft seal.

Found plastic impeller worn through into two pieces & little spring thingy under the grinder-upper thingy broken.

Ordered Drain & Wash Impeller kit - got it a few days later - installed (new motor shaft seal didn't seem to be quite the same as far as fit, so I didn't use it - just used the impeller & new spring thingy)

Put it all back together & runs fine - no more leaks - (now just have to figure out what to do about warped wood flooring - oh well, it's old & is probably time for whole new kitchen floor anyway)

Note: This particular Kenmore model made by Whirlpool - takes Whirlpool parts.

Note 2: Needed only screwdrivers to do this whole thing - would have been a really quick/easy repair if I had known what the problem was & how it all comes apart. took a little time to figure it out. (I am a rank amateur at dishwasher repair)

I removed the rubber boot on the top of the water dispersal unit ( stainless steel wand ) by turning it counterclockwise and the wand came off with ease. I then removed the top unit under it by removing the 8 torx screws and removed it. Under the unit is a cover with 1 torx screw to be removed and removed the cover to access the unit. I was unable to loosen the 1/4" nut on the shaft as it was very tight so I had to remove the unit and lock the motor armature with a piece of wood and removed the bolt. Using the kit I purchased I installed the new parts as required and it works as good as new.

The whole problem started with the upper vent on the door being plugged up with a whole bunch of labels that had been washed off of a bunch of tin cans that were washed prior to recycling them. Te high water float was also gummed up for the same reason and overflowed on the floor, I pulled it up and out and cleaned it up also, it works as good as new.

Removed dishwasher lower faceplate.
Removed hose clamp at the dishwasher end.
Removed clamp at the garbage-disposal end.
Removed hose.
Pulled new hose.
Connected both ends of the hose.
Installed both clamps.
Tested.

Look at the exploded parts diagram, that parts select provides on their website.

You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.

Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.

When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).

Then you're done. Just put it all back together.

Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.

After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwasher a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.

Water was not being sprayed thru the arms. I opened the dishwasher, removed/unscrewed the spray arms and wash impeller (black plastic wheel that directs the water) and then noticed that the part below the wash impeller had broken into pieces. There was only a metal ring and it was supposed to have a spring attached to it. I replaced the ring/spring below the wash impeller using the part from the Drain and Wash impeller kit. The dishwasher works great now.

It was my first mechanical fix. Use the web to diagnose, find the specs of the appliance and use common sense and you can do it yourself too.

By the way, the parts from this site arrived the next day.

I removed all the ( what my Husband called star screws ) star screws and removed the housing panel ( holds dish detergent cup and silverware basket ) I discovered everything accross the bottom was all gucked up with detergent soap accumulation. I took the part to the kitchen sink and used the sprayer hose on the part with hot water and it cleaned up beautifully, and the detergent latch then worked ( the spring that operates the latch was all gucked up with detergent accumulation ).
I am the wife and did all of this myself and it only took around 5-10 min. My Husband had to help me figure out the type of screws because they turned out to not be phillip screws, but as Hubby called them.."star screws".
Soooo, I did not need to use the Latch Kit I purchased, so will store it in my parts supply! :)
Happy repairs to you..
Judy Estes Park, CO

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards