7DU1100XTSQ5 Whirlpool Dishwasher - Instructions

The repair was easy. Getting the unit to slide out from under the counter was more time consuming.
After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now.
I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.

First research then troubleshoot
Removed
1 Upper rack
2 Lower rack
3 Lower Wash Arm and Strainer Parts
4 Upper Wash and Rinse Parts
5 Accumulator assy.
6 Motor shield
7 Inlet protector (most difficult)
Noticed blade was broken off chopper assy.
Replaced chopper assy.
Runs and cleans like new.
Most difficult step was to remove Inlet protector
After removing two torx screws (#15) used small pry bar to lift inlet protector from position. Not easy to accomplish with hands alone. Inlet protector fits tightly into position.

The Upper Rack Wheel Mount (where wheel attaches to mount) had broken. Was able to band-aid until parts received by running a small bolt and nut (with sufficient size washers) through the wheel attaching it to the assembly, then re-attaching the Upper Rack Wheel Mount back to the dishwasher upper tray. Once the part ordered from PartSelect arrived, it was a simple matter of mounting the new Upper Rack Wheel Mount to the tray, replacing the band-aided item. The upper tray did have to be removed from the slider bars - required the plastic keepers on the end of the slider bar to be removed and then reinstalled once the Upper Rack Wheel Mount was replaced.

Simply made sure the cap was securely in place.

no actual 'repair' was necessary, but, i was blown away at the speedy process of ordering and delivery of the part.

Replaced the switch, that did not fix it, but a new circuit card did

Disconnected power to dishwasher. Removed water supply hose from inlet water valve.
Removed lower and upper racks. Removed Lower spray arm. Removed tube from pump tp top spinner. Pulled dishwasher from under cabinet (remember to tip to get back out!). Placed dishwasher on its back. Removed electrical connectors from water valve, main motor and drain motor. Removed drain hose from drain pump. Removed pump/motor assy by pulling out wedges and pushing assembly into dishwasher. Removed pump/motor assy from inside dishwasher. Cleaned out pump. Installed new chopper. Re-install pump/motor assy. Re-install driain pump hose. Re-connect the pumps and water valve electric connectors. Slide dishwasher near cabinet for re-install. Re-connect drain hose to dishwasher. Re-install dishwasher under cabinet.Reconnect water supply. Removed top spinner from tube. Installed new spinner onto tube. Re-install tube onto main pump (below lower spray arm). Clean out and re-install lower spray arm. Remove middle spray arm from top rack. Clean out spray arm. Re-install spray arm with a new gasket (gasket may have not been needed). Re-installed lower and top racks. Re-connect power supply. Position all three spray arms pointing towards the door to confirm they were turning. Tested dishwasher - confirmed fill, wash, and drain properly. Also confirmed that all three spray arms were turning. Machine is washing, draining and running great since!

I took out the old one and started in the lower left corner and threaded it all around the edge to make sure the placement and length was correct. Then I came back around with a plastic spatula to firmly seat the gasket into the groove. Worked perfectly and havent had any trouble since!

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

I watched the video identifying the part and the procedure to make sure I could handle this. The phone attendant was also very helpful in making sure I ordered the correct part,which arrived in one day (amazingly). Everything was clearly described in the instructions and if you have done electrical work this would be relatively easy. You will need a specific screw driver bit to open the control panel but everything else is straightforward, just follow the instructions. Works perfectly now (I needed a new control panel about a year ago and Kenmore charged me $229 but it was just over a year since then....) PartSelect is a great service!

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!