79094001400 Kenmore Range - Instructions

- Cut the power to the oven (I used breaker). - Unscrew 2 screws. - Disconnect from 2 electric terminals. - Remove old bake element. - Connect new bake element to 2 electric terminals. - Screw the 2 screws back on. - Turn the breaker back on. ------------------------------------------------> Done! . . Saved the $79 that the appliance guy would've charged just for diagnostics. The part shipped to me within 24 hours so I didn't have to worry about scheduling a 2nd appointment and waiting around with no oven. You can do this on your own! Thanks partselect.com :)

Simple. Unscrew 2 screws unplug 2 tabs. Push on 2 tabs. Put 2 screws back adjust feet.

My husband did the repair he removed the old element and replaced it with the new one it was very easy to replace.

Piece of cake! Unscrewed the old, pulled it out, & put in the new element. Turned the oven on & presto! Oven can now bake!

Easy as one two three. Snap electrical wires to new element push thru back wall of oven and turn screws tight. This company was so amazing and my order arrived in a few days. I found you on the internet. Bless you all .

Touch up paint was easy to apply. I gave it a few coats and you cannot tell where to chip was. I wish you had a standard mail delivery option. I paid twice the price of the paint for fed ex delivery. I didn, t need the paint next day but it did get here before the estimated deliverydatee.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

First off the shipping was lightning speed and the repair was super easy anyone can do it.

All I did unscrew bolts pull out element wires detach them attach new element to the wires push them back inside the openings reattach bolts all done easypeasy and I am a 63 yr old woman

Removed screws,pulled off clips,reinstalled new element.

Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes

Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.

I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!